ATMEGA64A-AU Atmel, ATMEGA64A-AU Datasheet - Page 284

• Manufacturer Part Number: ATMEGA64A-AU
• Description: MCU AVR 64K ISP FLASH 64-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA64A-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Package: 64TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 53
• Interface Type: SPI/USART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 4
• Processor Series: ATMEGA64x
• Core: AVR8
• Data Ram Size: 4 KB
• Maximum Clock Frequency: 16 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Cpu Family: ATmega
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 4KB
• # I/os (max): 53
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: TQFP
• For Use With: 770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

26.5
8160C–AVR–07/09
Boot Loader Lock Bits
Figure 26-2. Memory Sections
Note:
If no Boot Loader capability is needed, the entire Flash is available for application code. The
Boot Loader has two separate sets of Boot Lock bits which can be set independently. This gives
the user a unique flexibility to select different levels of protection.
The user can select:
See
in Serial or Parallel Programming mode, but they can be cleared by a chip erase command only.
The general Write Lock (Lock bit mode 2) does not control the programming of the Flash mem-
• To protect the entire Flash from a software update by the MCU.
• To protect only the Boot Loader Flash section from a software update by the MCU.
• To protect only the Application Flash section from a software update by the MCU.
• Allow software update in the entire Flash.
Table 26-2
1. The parameters are given in
Boot Loader Flash Section
Boot Loader Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Program Memory
Program Memory
and
BOOTSZ = '11'
BOOTSZ = '01'
Table 26-3
for further details. The Boot Lock bits can be set in software and
(1)
$0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
$0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
Table 26-6 on page
Boot Loader Flash Section
Boot Loader Flash Section
Application Flash Section
Application Flash Section
Application flash Section
292.
Program Memory
Program Memory
BOOTSZ = '10'
BOOTSZ = '00'
ATmega64A
$0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
$0000
End RWW, End Application
Start NRWW, Start Boot Loader
Flashend
284