MC9S08SH16MTG Freescale Semiconductor, MC9S08SH16MTG Datasheet - Page 288

• Manufacturer Part Number: MC9S08SH16MTG
• Description: MCU 8BIT 16K FLASH 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08SH16MTG

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 16-TSSOP
• Core: S08
• Processor Series: MC9S08Sxx
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Data Ram Size: 1 KB
• On-chip Adc: Yes
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Operating Temperature Range: - 40 C to + 125 C
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 8
• Height: 1.05 mm
• Interface Type: SCI, SPI, I2C
• Length: 5 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 4.4 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Appendix A Electrical Characteristics
inputs are tied to an appropriate logic voltage level (for instance, either V
pull-up resistor associated with the pin is enabled.
288
1
2
3
Supply voltage
Maximum current into V
Digital input voltage
Instantaneous maximum current
Storage temperature range
current-limiting resistor, calculate resistance values for positive (V
voltages, then use the larger of the two resistance values.
All functional non-supply pins except RESET are internally clamped to V
MC9S08SH32, the RESET pin is named “PTA5/IRQ/TCLK/RESET.”
Power supply must maintain regulation within operating V
operating maximum current conditions. If positive injection current (V
I
out of regulation. Ensure external V
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if
no system clock is present, or if the clock rate is very low (which would reduce overall power
consumption).
Input must be current limited to the value specified. To determine the value of the required
DD
Single pin limit (applies to all port pins)
, the injection current may flow out of V
Rating
Table A-2. Absolute Maximum Ratings
DD
MC9S08SH32 Series Data Sheet, Rev. 2
DD
PRELIMINARY
load will shunt current greater than maximum injection
1, 2, 3
DD
and could result in external power supply going
Symbol
V
T
I
V
DD
I
DD
stg
D
In
DD
range during instantaneous and
DD
–0.3 to V
) and negative (V
–0.3 to +5.8
In
–55 to 150
SS
> V
Value
± 25
SS
120
or V
DD
DD
and V
) is greater than
+ 0.3
DD
DD
) or the programmable
. In
Freescale Semiconductor
SS
) clamp
Unit
mA
mA
°C
V
V