MCF5214CVF66J Freescale Semiconductor, MCF5214CVF66J Datasheet - Page 263

• Manufacturer Part Number: MCF5214CVF66J
• Description: IC MCU 256K FLASH 256MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF521xr

Specifications of MCF5214CVF66J

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 142
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Processor Series: MCF521x
• Core: ColdFire V2
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: M52210DEMO, M52211EVB
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No

14.2.5
14.2.5.1 External Interrupts (IRQ[7:1])
These inputs are the external interrupt sources. See
information on these interrupt sources and their corresponding registers.
These pins are configured as GPIO PNQ[7:1] in single-chip mode.
14.2.6
The following signals are used by the Ethernet module for data and clock signals.
14.2.6.1 Management Data (EMDIO)
The bidirectional EMDIO signal transfers control information between the external PHY and the
media-access controller. Data is synchronous to EMDC and applies to MII mode operation. This signal is
an input after reset. When the FEC is operated in 10 Mbps 7-wire interface mode, this signal should be
connected to VSS.
This pin can also be configured as GPIO PAS5 or URXD2.
14.2.6.2 Management Data Clock (EMDC)
EMDC is an output clock which provides a timing reference to the PHY for data transfers on the EMDIO
signal and applies to MII mode operation.
This pin can also be configured as GPIO PAS4 or UTXD2.
14.2.6.3 Transmit Clock (ETXCLK)
This is an input clock which provides a timing reference for ETXEN, ETXD[3:0] and ETXER.
This pin can also be configured as GPIO PEH7.
14.2.6.4 Transmit Enable (ETXEN)
The transmit enable (ETXEN) output indicates when valid nibbles are present on the MII. This signal is
asserted with the first nibble of a preamble and is negated before the first ETXCLK following the final
nibble of the frame.
This pin can also be configured as GPIO PEH6.
14.2.6.5 Transmit Data 0 (ETXD0)
ETXD0 is the serial output Ethernet data and is only valid during the assertion of ETXEN. This signal is
used for 10 Mbps Ethernet data. This signal is also used for MII mode data in conjunction with ETXD[3:1].
This pin can also be configured as GPIO PEH5.
Freescale Semiconductor
External Interrupt Signals
Ethernet Module Signals
These signals are not available on the MCF5214 and MCF5216.
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
NOTE
Chapter 11, “Edge Port Module
(EPORT)” for more
Signal Descriptions
14-23