UPD70F3768GF-GAT-AX Renesas Electronics America, UPD70F3768GF-GAT-AX Datasheet - Page 1224
UPD70F3768GF-GAT-AX
Manufacturer Part Number
UPD70F3768GF-GAT-AX
Description
MCU 32BIT V850ES/JX3-U 128-LQFP
Manufacturer
Renesas Electronics America
Series
V850ES/Jx3-Ur
Datasheet
1.UPD70F3763GC-UEU-AX.pdf
(1411 pages)
Specifications of UPD70F3768GF-GAT-AX
Core Processor
RISC
Core Size
32-Bit
Speed
48MHz
Connectivity
CSI, EBI/EMI, I²C, UART/USART, USB
Peripherals
DMA, LVD, PWM, WDT
Number Of I /o
96
Program Memory Size
384KB (384K x 8)
Program Memory Type
FLASH
Ram Size
48K x 8
Voltage - Supply (vcc/vdd)
2.85 V ~ 3.6 V
Data Converters
A/D 12x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
UPD70F3768GF-GAT-AX
Manufacturer:
Renesas Electronics America
Quantity:
10 000
- Current page: 1224 of 1411
- Download datasheet (8Mb)
V850ES/JG3-U, V850ES/JH3-U
25.3 HALT Mode
25.3.1 Setting and operation status
the other on-chip peripheral functions continues.
The on-chip peripheral functions that are independent of instruction processing by the CPU continue operating.
normal operation mode for intermittent operation.
25.3.2 Releasing HALT mode
external interrupt request signal (INTP00 to INTP18 pin input), unmasked internal interrupt request signal from a
peripheral function operable in the HALT mode, or reset signal (reset by RESET pin input, WDT2RES signal, low-voltage
detector (LVI), or clock monitor (CLM)).
R01UH0043EJ0300 Rev.3.00
Sep 30, 2010
Non-maskable interrupt request
signal
Maskable interrupt request signal
The HALT mode is set when a dedicated instruction (HALT) is executed in the normal operation mode.
In the HALT mode, the clock oscillator continues operating. Only clock supply to the CPU is stopped; clock supply to
As a result, program execution is stopped, and the internal RAM retains the contents before the HALT mode was set.
Table 25-3 shows the operating status in the HALT mode.
The average current consumption of the system can be reduced by using the HALT mode in combination with the
Cautions 1. Insert five or more NOP instructions after the HALT instruction.
The HALT mode is released by a non-maskable interrupt request signal (NMI pin input, INTWDT2 signal), unmasked
After the HALT mode has been released, the normal operation mode is restored.
(1) Releasing HALT mode by non-maskable interrupt request signal or unmasked maskable interrupt request
signal
The HALT mode is released by a non-maskable interrupt request signal or an unmasked maskable interrupt
request signal, regardless of the priority of the interrupt request signal. If the HALT mode is set in an interrupt
servicing routine, however, an interrupt request signal that is issued later is serviced as follows.
(a) If an interrupt request signal with a priority lower than that of the interrupt request currently being serviced is
(b) If an interrupt request signal with a priority higher than that of the interrupt request currently being serviced is
Release Source
issued, the HALT mode is released, but that interrupt request signal is not acknowledged. The interrupt
request signal itself is retained.
issued (including a non-maskable interrupt request signal), the HALT mode is released and that interrupt
request signal is acknowledged.
2. If the HALT instruction is executed while an unmasked interrupt request signal is being held
pending, the status shifts to HALT mode, but the HALT mode is then released immediately by the
pending interrupt request.
Table 25-2. Operation After Releasing HALT Mode by Interrupt Request Signal
Execution branches to the handler address.
Execution branches to the handler address
or the next instruction is executed.
Interrupt Enabled (EI) Status
The next instruction is executed.
CHAPTER 25 STANDBY FUNCTION
Interrupt Disabled (DI) Status
Page 1224 of 1408
Related parts for UPD70F3768GF-GAT-AX
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: