ATTINY15L-1SU Atmel, ATTINY15L-1SU Datasheet - Page 15

• Manufacturer Part Number: ATTINY15L-1SU
• Description: IC MCU AVR 1K FLASH 1.6MHZ 8SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY15L-1SU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 1.6MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 6
• Program Memory Size: 1KB (512 x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Ram Size: -
• Connectivity: -

Power-on Reset
1187H–AVR–09/07
Table 5. Reset Delay Selections
Notes:
Table 5 shows the start-up times from Reset. When the CPU wakes up from Power-
down, only the clock-counting part of the start-up time is used. The Watchdog Oscillator
is used for timing the real-time part of the start-up time. The number Watchdog Oscilla-
tor cycles used for each time-out is shown in Table 6.
The frequency of the Watchdog Oscillator is voltage dependent as shown in the Electri-
cal Characteristics section on page 64. The device is shipped with CKSEL = “00”.
Table 6. Number of Watchdog Oscillator Cycles
A Power-on Reset (POR) pulse is generated by an On-chip Detection circuit. The detec-
tion level is nominally defined in Table 4. The POR is activated whenever V
the detection level. The POR circuit can be used to trigger the Start-up Reset, as well as
detect a failure in supply voltage.
A Power-on Reset (POR) circuit ensures that the device is Reset from Power-on.
Reaching the Power-on Reset threshold voltage invokes a delay counter, which deter-
mines the delay, for which the device is kept in RESET after V
period of the delay counter can be defined by the user through the CKSEL Fuses. The
different selections for the delay period are presented in Table 5. The RESET signal is
activated again, without any delay, when the V
BODEN
x
x
x
1
0
1. On Power-up, the start-up time is increased with typical 0.6 ms.
2. “0” means programmed, “1” means unprogrammed.
V
(2)
CC
Conditions
CKSEL [1:0]
2.7V
2.7V
2.7V
2.7V
5.0V
5.0V
5.0V
5.0V
00
01
10
11
11
(2)
t
TOUT
256 ms + 18 CK
256 ms + 18 CK
18 CK + 128 µs
Start-up Time,
16 ms + 18 CK
18 CK + 32 µs
(1)
at V
Time-out
256 ms
128 µs
CC
16 ms
64 ms
32 µs
32 µs
4 ms
8 µs
= 2.7V
CC
decreases below detection level.
t
TOUT
Start-up Time,
64 ms + 18 CK
64 ms + 18 CK
18 CK + 32 µs
4 ms + 18 CK
18 CK + 8 µs
at V
CC
= 5.0V
Number of Cycles
CC
64K
64K
ATtiny15L
32
4K
32
4K
rise. The Time-out
8
8
Recommended
Usage
BOD disabled,
slowly rising
power
BOD disabled,
slowly rising
power
BOD disabled,
quickly rising
power
BOD disabled
BOD enabled
CC
is below
15