AT91SAM9261SB-CU-999 Atmel, AT91SAM9261SB-CU-999 Datasheet - Page 179

• Manufacturer Part Number: AT91SAM9261SB-CU-999
• Description: IC MCU ARM9 ULTRA LP 217LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9261SB-CU-999

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 190MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: DMA, LCD, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: 2-Wire, I2S, SPI, USB
• Maximum Clock Frequency: 190 MHz
• Number Of Programmable I/os: 96
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9261-EK
• Minimum Operating Temperature: - 40 C
• For Use With: AT91SAM9261-EK - KIT EVAL FOR AT91SAM926EJ-SAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

Figure 22-19. Early Read Wait State: NWE-controlled Write with No Hold Followed by a Read with one Set-up Cycle
22.9.3
22.9.3.1
6242E–ATARM–11-Sep09
Reload User Configuration Wait State
external write controlling signal
internal write controlling signal
User Procedure
The user may change any of the configuration parameters by writing the SMC user interface.
When detecting that a new user configuration has been written in the user interface, the SMC
inserts a wait state before starting the next access. The so called “Reload User Configuration
Wait State” is used by the SMC to load the new set of parameters to apply to next accesses.
The Reload Configuration Wait State is not applied in addition to the Chip Select Wait State. If
accesses before and after re-programming the user interface are made to different devices
(Chip Selects), then one single Chip Select Wait State is applied.
On the other hand, if accesses before and after writing the user interface are made to the same
device, a Reload Configuration Wait State is inserted, even if the change does not concern the
current Chip Select.
To insert a Reload Configuration Wait State, the SMC detects a write access to any
SMC_MODE register of the user interface. If the user only modifies timing registers
(SMC_SETUP, SMC_PULSE, SMC_CYCLE registers) in the user interface, he must validate
the modification by writing the SMC_MODE, even if no change was made on the mode
parameters.
The user must not change the configuration parameters of an SMC Chip Select (Setup, Pulse,
Cycle, Mode) if accesses are performed on this CS during the modification. Any change of the
Chip Select parameters, while fetching the code from a memory connected on this CS, may lead
NBS0, NBS1,
NBS2, NBS3,
A0, A1
D[31:0]
A[25:2]
(NWE)
MCK
NRD
(WRITE_MODE = 1)
write cycle
no hold
Early Read
wait state
read setup = 1
(READ_MODE = 0 or READ_MODE = 1)
read cycle
AT91SAM9261S
179