AT91SAM9261SB-CU-999 Atmel, AT91SAM9261SB-CU-999 Datasheet - Page 687

• Manufacturer Part Number: AT91SAM9261SB-CU-999
• Description: IC MCU ARM9 ULTRA LP 217LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9261SB-CU-999

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 190MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: DMA, LCD, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: 2-Wire, I2S, SPI, USB
• Maximum Clock Frequency: 190 MHz
• Number Of Programmable I/os: 96
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9261-EK
• Minimum Operating Temperature: - 40 C
• For Use With: AT91SAM9261-EK - KIT EVAL FOR AT91SAM926EJ-SAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

42.3.11
42.3.11.1
42.3.12
42.3.12.1
42.3.13
42.3.13.1
42.3.14
42.3.14.1
42.3.14.2
6242E–ATARM–11-Sep09
Shutdown Controller (SHDWC)
Static Memory Controller (SMC)
System Controller
Two-wire Interface (TWI)
SHDWC: Boundary Scan Mode Outputs the 32 kHz Clock
SMC: Chip Select Parameters Modification
SYSC: Possible Event Loss When Reading RTT_SR
TWI: Clock Divider
TWI: Disabling Does Not Operate Correctly
In boundary scan mode, the SHDN pin outputs the 32 kHz clock.
There is only one way to disable the 32 kHz clock on the SHDN pin.
In boundary scan mode, connect TST and JTAGSEL pins to VDDBU and set the SHDN pin to
low level.
The user must not change the configuration parameters of an SMC Chip Select (Setup, Pulse,
Cycle, Mode) if accesses are performed on this CS during the modification.
For example, the modification of the Chip Select 0 (CS0) parameters, while fetching the code
from a memory connected on this CS0, may lead to unpredictable behavior.
The code used to modify the parameters of an SMC Chip Select can be executed from the inter-
nal RAM or from a memory connected to another Chip Select
If an event (RTTINC or ALMS) occurs within the same slow clock cycle as when the RTT_SR is
read, the corresponding bit might be cleared. This can lead to the loss of this event.
The software must handle an RTT event as interrupt and as the only source of the interrupt
source level 1.
The value of CLDIV x 2
must be less than or equal to 8191·
None.
Any transfer in progress is immediately frozen if the Control Register (TWI_CR) is written with
the bit MSDIS at 1. Furthermore, the status bits TXCOMP and TXRDY in the Status Register
(TWI_SR) are not reset.
The user must wait for the end of transfer before disabling the TWI. In addition, the interrupts
must be disabled before disabling the TWI.
Problem/Fix Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
CKDIV
must be less than or equal to 8191, the value of CHDIV x 2
AT91SAM9261S
CKDIV
687