AT91SAM9261SB-CU-999 Atmel, AT91SAM9261SB-CU-999 Datasheet - Page 690

• Manufacturer Part Number: AT91SAM9261SB-CU-999
• Description: IC MCU ARM9 ULTRA LP 217LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9261SB-CU-999

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 190MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: DMA, LCD, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: 2-Wire, I2S, SPI, USB
• Maximum Clock Frequency: 190 MHz
• Number Of Programmable I/os: 96
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9261-EK
• Minimum Operating Temperature: - 40 C
• For Use With: AT91SAM9261-EK - KIT EVAL FOR AT91SAM926EJ-SAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

42.3.16.3
42.3.17
42.3.17.1
690
AT91SAM9261S
UDP
UHP: Remote Wakeup Event
UDP: Bad Data in the First IN Data Stage
Consequence: After the failure condition, the Host controller stops sending the SOF. This
causes the connected device to go into suspend state.
This problem can be avoided if the system can guarantee that no buffer underrun occurs during
the transfer.
Conditions:
When a Remote Wakeup event occurs on a downstream port, the OHCI Host controller begins
sending resume signaling to the device. The Host controller is supposed to send this resume
signaling for 20 ms. However, if the driver sets the HcControl.HCFS into USBOPERATIONAL
state during the resume event, then the Host controller terminates sending the resume signal
with an EOP to the device.
Consequence: If the Device does not recognize the resume (<20 ms) event, then the Device will
remain in suspend state.
Host stack can do a port resume after it sets the HcControl.HCFS to USBOPERATIONAL.
All or part of the data of the first IN data Stage are not transmitted. It may then be a Zero Length
Packet. The CRC is correct. So the HOST may only see that the size of the received data does
not match the requested length. But even if performed again, the control transfer will probably
fail.
These Control transfers are mainly used at device configuration. After clearing RXSETUP, the
software needs to compute the setup transaction request before writing data into the FIFO if
needed. This time is generally greater than the minimum safe delay required above. If not, a
software wait loop after RXSETUP clear may be added at minimum cost.
1. The Host controller sends an ISO OUT token after fetching 16 bytes of data from the
2. When the Host controller is sending the ISO OUT data, because of system latencies,
3. While there is an underrun condition, if the Host controller is in the process of bit-stuff-
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
system memory.
remaining bytes of the packet are not available. This results in a buffer underrun
condition.
ing, it causes the Host controller to hang.
6242E–ATARM–11-Sep09