XR20M1172IL32-F Exar Corporation, XR20M1172IL32-F Datasheet - Page 38

• Manufacturer Part Number: XR20M1172IL32-F
• Description: IC UART FIFO I2C/SPI 64B 32QFN
• Manufacturer: Exar Corporation

Specifications of XR20M1172IL32-F

• Number Of Channels: 2, DUART
• Package / Case: 32-VFQFN Exposed Pad
• Features: *
• Fifo's: 64 Byte
• Protocol: RS485
• Voltage - Supply: 1.62 V ~ 3.63 V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Data Rate: 16 Mbps
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 1.62 V
• Supply Current: 250 uA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• No. Of Channels: 2
• Uart Features: Tx/Rx FIFO Counters
• Supply Voltage Range: 1.62V To 3.63V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: QFN
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

XR20M1172
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
This register is used to program the direction of the GPIO pins. Bit-7 to bit-0 controls GPIO7 to GPIO0.
•
•
This register reports the state of all GPIO pins during a read and writes to any GPIO that is an output.
•
•
This register enables the interrupt for the GPIO pins. The interrupts for GPIO[7:4] are only enabled if
IOControl[1] = 0. If IOControl[0] = 1 (GPIO pins are selected as modem IOs) , then IOIntEna[7:4] will have no
effect on GPIO[7:4].
•
•
IOControl[7:4]: Reserved
IOControl[3]: UART Software Reset
Writing a logic 1 to this bit will reset the device. Once the device is reset, this bit will automatically be set to a
logic 0.
IOControl[2]: GPIO[3:0] or Modem IO Select (CH B)
This bit controls whether GPIO[3:0] behave as GPIO pins or as modem IO pins (RIB#, CDB#, DTRB#, DSRB#)
•
•
IOControl[1]: GPIO[7:4] or Modem IO Select (CH A)
This bit controls whether GPIO[7:4] behave as GPIO pins or as modem IO pins (RIA#, CDA#, DTRA#, DSRA#)
•
•
IOControl[0]: IO Latch
This bit enable/disable GPIO inputs latching.
•
•
4.15
4.16
4.17
4.18
Logic 0 = set GPIO pin as input
Logic 1 = set GPIO pin as output
Logic 0 = set output pin LOW
Logic 1 = set output pin HIGH
Logic 0 = a change in the input pin will not generate an interrupt
Logic 1 = a change in the input will generate an interrupt
Logic 0 = GPIO[3:0] behave as GPIO pins
Logic 1 = GPIO[3:0] behave as RIB#, CDB#, DTRB#, DSRB#. Note: DTRB# will also need to be set as an
output via IODir bit-1.
Logic 0 = GPIO[7:4] behave as GPIO pins
Logic 1 = GPIO[7:4] behave as RIA#, CDA#, DTRA#, DSRA#. Note: DTRA# will also need to be set as an
output via IODir bit-5.
Logic 0 = GPIO input values are not latched. A change in any GPIO input generates an interrupt. A read of
the IOState register clears the interrupt. If the input goes back to its initial logic state before the input register
is read, then the interrupt is cleared.
Logic 1 = GPIO input values are latched. A change in the GPIO input generates an interrupt and the input
logic value is loaded in the bit of the corresponding input state register (IOState). A read of the IOState
register clears the interrupt. If the input pin goes back to its initial logic state before the interrupt register is
read, then the interrupt is not cleared and the corresponding bit of the IOState register keeps the logic value
that generated the interrupt.
GPIO Direction Register (IODir) - Read/Write
GPIO State Register (IOState) = Read/Write
GPIO Interrupt Enable Register (IOIntEna) - Read/Write
GPIO Control Register (IOControl) - Read/Write
38
REV. 1.0.1