ISL6323EVAL1Z Intersil, ISL6323EVAL1Z Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL6323EVAL1Z
Manufacturer Part Number
ISL6323EVAL1Z
Description
EVAL BOARD 1 FOR ISL6323
Manufacturer
Intersil
Datasheet
1.ISL6323CRZ.pdf
(35 pages)
Specifications of ISL6323EVAL1Z
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Active Pulse Positioning Modulated PWM Operation
The ISL6323 uses a proprietary Active Pulse Positioning (APP)
modulation scheme to control the internal PWM signals that
command each channel’s driver to turn their upper and lower
MOSFETs on and off. The time interval in which a PWM signal
can occur is generated by an internal clock, whose cycle time is
the inverse of the switching frequency set by the resistor
between the FS pin and ground. The advantage of Intersil’s
proprietary Active Pulse Positioning (APP) modulator is that the
PWM signal has the ability to turn on at any point during this
PWM time interval, and turn off immediately after the PWM
signal has transitioned high. This is important because it allows
the controller to quickly respond to output voltage drops
associated with current load spikes, while avoiding the ring
back affects associated with other modulation schemes.
The PWM output state is driven by the position of the error
amplifier output signal, V
signal relative to the proprietary modulator ramp waveform as
illustrated in Figure 3. At the beginning of each PWM time
interval, this modified V
internal modulator waveform. As long as the modified V
voltage is lower then the modulator waveform voltage, the
PWM signal is commanded low. The internal MOSFET driver
detects the low state of the PWM signal and turns off the
upper MOSFET and turns on the lower synchronous
MOSFET. When the modified V
modulator ramp, the PWM output transitions high, turning off
the synchronous MOSFET and turning on the upper
MOSFET. The PWM signal will remain high until the modified
V
occurs the PWM signal will transition low again.
During each PWM time interval the PWM signal can only
transition high once. Once PWM transitions high it can not
transition high again until the beginning of the next PWM
time interval. This prevents the occurrence of double PWM
pulses occurring during a single period.
COMP
FIGURE 2. CHANNEL INPUT CURRENTS AND INPUT
voltage crosses the modulator ramp again. When this
INPUT-CAPACITOR CURRENT, 10A/DIV
CAPACITOR RMS CURRENT FOR 3-PHASE
CONVERTER
CHANNEL 1
INPUT CURRENT
10A/DIV
CHANNEL 2
INPUT CURRENT
10A/DIV
COMP
COMP
CHANNEL 3
INPUT CURRENT
10A/DIV
12
1μs/DIV
signal is compared to the
, minus the current correction
COMP
voltage crosses the
COMP
ISL6323
To further improve the transient response, ISL6323 also
implements Intersil’s proprietary Adaptive Phase Alignment
(APA) technique, which turns on all phases together under
transient events with large step current. With both APP and
APA control, ISL6323 can achieve excellent transient
performance and reduce the demand on the output capacitors.
Adaptive Phase Alignment (APA)
To further improve the transient response, the ISL6323 also
implements Intersil’s proprietary Adaptive Phase Alignment
(APA) technique, which turns on all of the channels together
at the same time during large current step transient events.
As Figure 3 shows, the APA circuitry works by monitoring the
voltage on the APA pin and comparing it to a filtered copy of
the voltage on the COMP pin. The voltage on the APA pin is
a copy of the COMP pin voltage that has been negatively
offset. If the APA pin exceeds the filtered COMP pin voltage
an APA event occurs and all of the channels are forced on.
The APA trip level is the amount of DC offset between the
COMP pin and the APA pin. This is the voltage excursion
that the APA and COMP pins must have during a transient
event to activate the Adaptive Phase Alignment circuitry.
This APA trip level is set through a resistor, R
connects from the APA pin to the COMP pin. A 100µA
current flows across R
trip level as described in Equation 4. An APA trip level of
500mV is recommended for most applications. A 0.1µF
capacitor, C
resistor to help with noise immunity.
PWM Operation
The timing of each core channel is set by the number of
active channels. Channel detection on the ISEN3- and
ISEN4- pins selects 2-channel to 4-channel operation for the
ISL6323. The switching cycle is defined as the time between
PWM pulse termination signals of each channel. The cycle
time of the pulse signal is the inverse of the switching
frequency set by the resistor between the FS pin and
C
V
APA
APA TRIP
FIGURE 3. ADAPTIVE PHASE ALIGNMENT DETECTION
,
EXTERNAL CIRCUIT
R
APA
APA
=
R
, should also be placed across the R
APA
V
-
APA,TRIP
COMP
⋅
APA
100
APA
×
10
into the APA pin to set the APA
–
ISL6323 INTERNAL CIRCUIT
6
100µA
AMPLIFIER
FILTER
PASS
LOW
ERROR
APA
+
-
October 21, 2008
APA
, that
CIRCUITRY
TO APA
APA
FN9278.4
(EQ. 4)