MAX1359BETL+ Maxim Integrated Products, MAX1359BETL+ Datasheet - Page 44
![IC DAS 16BIT 40-TQFN](/photos/6/65/66502/40-qfn_pkg_sml.jpg)
MAX1359BETL+
Manufacturer Part Number
MAX1359BETL+
Description
IC DAS 16BIT 40-TQFN
Manufacturer
Maxim Integrated Products
Type
Data Acquisition System (DAS)r
Specifications of MAX1359BETL+
Resolution (bits)
16 b
Sampling Rate (per Second)
21.84k
Data Interface
Serial
Voltage Supply Source
Analog and Digital
Voltage - Supply
1.8 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
40-TQFN Exposed Pad
Number Of Converters
2
Resolution
16 bit
Interface Type
Serial (4-Wire, SPI, QSPI, Microwire)
Voltage Reference
1.25 V
Supply Voltage (max)
3.6 V
Supply Voltage (min)
1.8 V
Maximum Power Dissipation
2051.3 mW
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Input Voltage
1.8 V to 3.6 V
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
16-Bit, Data-Acquisition System with ADC, DAC,
UPIOs, RTC, Voltage Monitors, and Temp Sensor
The PWM_CTRL register contains control bits for the 8-
bit PWM.
PWME: PWM-enable bit. Set PWME = 1 to enable the
internal PWM and set PWME = 0 to disable the internal
PWM. Enable the high frequency clock before enabling
the PWM when using input clock frequencies above
32.768kHz. The power-on default state is 0.
FSEL<2:0>: Frequency selection bits. Selects the PWM
input clock frequency as shown in Table 14. The
power-on default is 000.
SWAH: SWA-switch PWM-high control bit. Set SWAH =
1 to enable the PWM output to directly control the SWA
switch. When SWAH = SWAL, the PWM output is dis-
abled from controlling the SWA switch. When SWAH =
1, a PWM high output closes the SWA switch and a
PWM low output opens the SWA switch. The PWM high
output refers to the beginning of the period when the
output is logic-high. See Table 17 for more details. The
power-on default is 0.
SWAL: SWA-switch PWM-low control bit. Set SWAL = 1
to enable the inverted PWM output to directly control
PWM_CTRL Register (Power-On State: 0000 0000 00XX XXXX)
Table 14. Setting the PWM Frequency
* The lower PWM frequencies are useful for power-supply duty cycling to conserve battery life and enable a single battery cell-powered sys-
tem. The higher frequencies allow reasonably small, external components for RC filtering when used as a DAC for bias adjustments.
** When the part is in sleep mode, the HFCK is shut down. In this case, PWM frequencies above 32kHz are not available (see SPWME in the
SLEEP_CFG Register section).
44
PWME
______________________________________________________________________________________
SPD1
MSB
PWM INPUT FREQUENCY* (kHz)
4915.2**
2457.6**
1228.8**
FSEL2
32.768
SPD2
8.192
1.024
0.256
0.032
FSEL1
X
FSEL0
X
FSEL2
0
0
0
0
1
1
1
1
the SWA switch. When SWAH = SWAL, the PWM output
is disabled from controlling the SWA switch. When
SWAL = 1, a PWM low output closes the SWA switch
and a PWM high output opens the SWA switch. The
PWM low output refers to the end of the period when
the output is logic-low. See Table 17 for more details.
The power-on default is 0.
SPD1: SPDT1-switch PWM drive control bit. Set SPD1
= 1 to enable the PWM output to directly control the
SPDT1 switch and set SPD1 = 0 to disable the PWM
output controlling the SPDT1 switch. The SPDT1<1:0>
bits, the UPIO pins (if programmed), and the PWM out-
put (if enabled), determine the SPDT1-switch state. See
Table 18 for more details. The power-on default is 0.
SPD2: SPDT2-switch PWM drive control bit. Set SPD2
= 1 to enable the PWM output to directly control the
SPDT2 switch and set SPD2 = 0 to disable the PWM
output controlling the SPDT2 switch. The SPDT2<1:0>
bits, the UPIO pins (if programmed), and the PWM out-
put (if enabled), determine the SPDT2-switch state. See
Table 19 for more details. The power-on default is 0.
SWAH
X
SWAL
FSEL1
X
0
0
1
1
0
0
1
1
Reserved
X
FSEL0
0
1
0
1
0
1
0
1
Reserved
LSB
X