EP3C55F484C8N Altera, EP3C55F484C8N Datasheet - Page 94

• Manufacturer Part Number: EP3C55F484C8N
• Description: IC CYCLONE III FPGA 55K 484FBGA
• Manufacturer: Altera
• Series: Cyclone® IIIr

Specifications of EP3C55F484C8N

• Number Of Logic Elements/cells: 55856
• Number Of Labs/clbs: 3491
• Total Ram Bits: 2396160
• Number Of I /o: 327
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 484-FBGA
• Family Name: Cyclone III
• Number Of Logic Blocks/elements: 55856
• # I/os (max): 327
• Frequency (max): 402MHz
• Process Technology: 65nm
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 55856
• Ram Bits: 2396160
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 484
• Package Type: FBGA
• No. Of Logic Blocks: 3491
• Family Type: Cyclone III
• No. Of I/o's: 327
• I/o Supply Voltage: 3.3V
• Operating Frequency Max: 402MHz
• Operating Temperature Range: 0°C To +85°C
• Rohs Compliant: Yes
• For Use With: 544-2601 - KIT DEV CYCLONE III LS EP3CLS200544-2411 - KIT DEV NIOS II CYCLONE III ED.
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 544-2510

5–30
Table 5–9. Dynamic Phase Shifting Control Signals
Cyclone III Device Handbook, Volume 1
PHASECOUNTERSELECT[2:0]
PHASEUPDOWN
PHASESTEP
SCANCLK
PHASEDONE
Signal Name
Table 5–8
PLLs.
Table 5–8. PLL Counter Settings
To bypass any of the PLL counters, set the bypass bit to 1. The values on the other bits
are then ignored.
Dynamic Phase Shifting
The dynamic phase shifting feature allows the output phase of individual PLL
outputs to be dynamically adjusted relative to each other and the reference clock
without sending serial data through the scan chain of the corresponding PLL. This
feature simplifies the interface and allows you to quickly adjust t
changing output clock phase shift in real time. This is achieved by incrementing or
decrementing the VCO phase-tap selection to a given C counter or to the M counter.
The phase is shifted by 1/8 the VCO frequency at a time. The output clocks are active
during this phase reconfiguration process.
Table 5–9
Note to
(1) Bypass bit.
X
X
Table
X
X
lists the settings for bypassing the counters in Cyclone III device family
lists the control signals that are used for dynamic phase shifting.
PLL Scan Chain Bits [0..8] Settings
5–8:
Counter Select. Three bits decoded to select
either the M or one of the C counters for
phase adjustment. One address map to select
all C counters. This signal is registered in the
PLL on the rising edge of SCANCLK.
Selects dynamic phase shift direction; 1= UP,
0 = DOWN. Signal is registered in the PLL on
the rising edge of SCANCLK.
Logic high enables dynamic phase shifting.
Free running clock from core used in
combination with PHASESTEP to enable or
disable dynamic phase shifting. Shared with
SCANCLK for dynamic reconfiguration.
When asserted, it indicates to core logic that
the phase adjustment is complete and PLL is
ready to act on a possible second adjustment
pulse. Asserts based on internal PLL timing.
Deasserts on rising edge of SCANCLK.
X
X
X
X
LSB
X
X
Description
X
X
Chapter 5: Clock Networks and PLLs in the Cyclone III Device Family
X
X
X
X
1
0
MSB
(1)
(1)
Logic array or I/O
pins
Logic array or I/O
pins
Logic array or I/O
pins
GCLK or I/O pins
PLL reconfiguration
circuit
PLL counter bypassed
PLL counter not bypassed
© December 2009 Altera Corporation
Source
Description
CO
delays by
PLL Reconfiguration
PLL
reconfiguration
circuit
PLL
reconfiguration
circuit
PLL
reconfiguration
circuit
PLL
reconfiguration
circuit
Logic array or
I/O pins
Destination