EP3C120F780I7 Altera, EP3C120F780I7 Datasheet - Page 42

• Manufacturer Part Number: EP3C120F780I7
• Description: IC CYCLONE III FPGA 120K 780FBGA
• Manufacturer: Altera
• Series: Cyclone® IIIr

Specifications of EP3C120F780I7

• Number Of Logic Elements/cells: 119088
• Number Of Labs/clbs: 7443
• Total Ram Bits: 3981312
• Number Of I /o: 531
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 780-FBGA
• Family Name: Cyclone III
• Number Of Logic Blocks/elements: 119088
• # I/os (max): 531
• Frequency (max): 437.5MHz
• Process Technology: 65nm
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 119088
• Ram Bits: 3981312
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 780
• Package Type: FBGA
• For Use With: 544-2589 - KIT DEV EMB CYCLONE III EDITION544-2566 - KIT DEV DSP CYCLONE III EDITION544-2444 - KIT DEV CYCLONE III EP3C120
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Not Compliant

Page 42
Configuration Software Settings
f
f
■
■
■
■
To find the correct pin, refer to the Device Pin-Outs page of the Literature section of
the Altera website (www.altera.com).
Simulation
The altpll megafunction supports behavioral and timing simulation.
For more information about simulation support and methods, refer to the
section in volume 3 of the Quartus II Handbook.
This section covers several configuration options that you can set in the Quartus II
software before you compile to generate configuration or programming files. Your
board and system design is affected by these settings and pins.
Optional Configuration Pins
Prior to generating the configuration files, you should take the following optional
configuration pins into your consideration according to your board and system
design. You can enable the following optional configuration pins on the General tab
of the Device and Pin Options dialog box.
CLKUSR
By default, the initialization clock source is from the 10 MHz (typical) internal
oscillator. The advantage of using the internal oscillator is that you do not need to
send additional clock cycles from an external source to the CLKUSR pin during the
initialization stage. However, if you have to synchronize the initialization of the
multiple devices or to delay the initialization, a Cyclone III device provides the
flexibility to control when your device enters user mode using CLKUSR pin. The
Enable user-supplied start-up clock (CLKUSR) option in the Quartus II software
allows you to select which clock source is used for initialization; either the internal
oscillator or external clocks provided on the CLKUSR pin. Supplying an external clock
on CLKUSR does not affect the configuration process. After all the configuration data
is accepted and the CONF_DONE goes high, Cyclone III devices require 3,185 clock
cycles to initialize properly and enter user mode. Cyclone III devices support a
CLKUSR f
clock, you can use it as a user I/O pin.
inclk[1,0] – dedicated clock input pin (CLK[15..0])
clkswitch, areset, pfdena, scandata, scanclk, configupdate,
scanclkena, phasecounterselect[2..0], phaseupdown, phasestep –
User I/O or logic array signal
c[4..0] – dedicated PLL clock output pin (only c0) or user I/O or logic array
signal (c0-c4)
clkbad[1,0], locked, activeclock, scandone, scandataout, phasedone
– User I/O or logic array signal
MAX
of 133 MHz. When you are not using the CLKUSR pin to supply external
© November 2008 Altera Corporation
Design and Compilation
Simulation