MPC8544VTALF Freescale Semiconductor, MPC8544VTALF Datasheet - Page 91

• Manufacturer Part Number: MPC8544VTALF
• Description: MPU POWERQUICC III 783-PBGA
• Manufacturer: Freescale Semiconductor

Specifications of MPC8544VTALF

• Processor Type: MPC85xx PowerQUICC III 32-Bit
• Speed: 667MHz
• Voltage: 1V
• Mounting Type: Surface Mount
• Package / Case: 783-FCPBGA
• Processor Series: MPC85xx
• Core: e500
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 667 MHz
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Data Ram Size: 32 KB
• I/o Voltage: 1.8 V, 3.3 V
• Interface Type: I2C, HSSI, DUART
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Freescale Semiconductor
AVDD_SRDS
AVDD_SRDS2
SENSEVDD
SENSEVSS
MVREF
SD1_IMP_CAL_RX
SD1_IMP_CAL_TX
SD1_PLL_TPA
SD2_IMP_CAL_RX
SD2_IMP_CAL_TX
SD2_PLL_TPA
NC
Notes:
5. Treat these pins as no connects (NC) unless using debug address functionality.
1.All multiplexed signals are listed only once and do not re-occur. For example, LCS5/DMA_REQ2 is listed only once in the
2.Recommend a weak pull-up resistor (2–10 KΩ) be placed on this pin to OV
3.This pin must always be pulled high.
4.This pin is a reset configuration pin. It has a weak internal pull-up P-FET which is enabled only when the processor is in the
Local Bus Controller Interface section, and is not mentioned in the DMA section even though the pin also functions as
DMA_REQ2.
reset state. This pull-up is designed such that it can be overpowered by an external 4.7-kΩ pull-down resistor. However, if
the signal is intended to be high after reset, and if there is any device on the net which might pull down the value of the net
at reset, then a pull-up or active driver is needed. TSEC3_TXD[3] (cfg_srds_sgmii_refclk) is an exception, because the
default value of this configuration signal is low (0). Thus, no external pull-down resistor is needed for selecting the default
configuration value.
Signal
MPC8544E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 5
W28
AG1
W11
W10
A28
M26
AE28
V26
AH3
Y1
AH1
C19, D7, D10, K13, L6, K9, B6, F12, J7, M19,
M25, N19, N24, P19, R19, AB19, T12, W3,
M12, W5, P12, T19, W1, W7, L13, U19, W4, V8,
V9, V10, V11, V12, V13, V14, V15, V16, V17,
V18, V19, W2, W6, W8, T11, U11, W12, W13,
W14, W15, W16, W17, W18, W19, W27, V25,
Y17, Y18, Y19, AA18, AA19, AB20, AB21,
AB22, AB23, J9
Table 62. MPC8544E Pinout Listing (continued)
Package Pin Number
No Connect Pins
Analog Signals
DD
voltage signal
.
SRDSPLL
SRDSPLL
Reference
Pin Type
Power for
Power for
for DDR
(1.0 V)
(1.0 V)
—
—
—
—
—
O
O
I
I
AVDD_SRDS2
200 Ω to GND
100 Ω to GND
200Ω to GND
100Ω to GND
AVDD_SRDS
ANALOG
ANALOG
MVREF
Supply
Power
V
—
—
—
—
DD
Package Description
Notes
19
19
12
12
17
17
—
—
—
—
—
—
91