PIC18F2510-I/ML Microchip Technology Inc., PIC18F2510-I/ML Datasheet - Page 237

• Manufacturer Part Number: PIC18F2510-I/ML
• Description: Microcontroller; 32 KB Flash; 1024 RAM; 0 EEPROM; 21 I/O; 28-Pin-QFN
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F2510-I/ML

• A/d Inputs: 10-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 21
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin QFN
• Programmable Memory: 32K Bytes
• Ram Size: 1.5K Bytes
• Speed: 40 MHz
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

20.2
For PIC18F45J10 family devices, the WDT is driven by
the INTRC oscillator. When the WDT is enabled, the
clock source is also enabled. The nominal WDT period
is 4 ms and has the same stability as the INTRC
oscillator.
The 4 ms period of the WDT is multiplied by a 16-bit
postscaler. Any output of the WDT postscaler is
selected by a multiplexor, controlled by the WDTPS bits
in Configuration Register 2H. Available periods range
from 4 ms to 131.072 seconds (2.18 minutes). The
WDT and postscaler are cleared whenever a SLEEP or
CLRWDT instruction is executed, or a clock failure
(primary or Timer1 oscillator) has occurred.
FIGURE 20-1:
REGISTER 20-9:
TABLE 20-2:
© 2006 Microchip Technology Inc.
RCON
WDTCON
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Watchdog Timer.
WDTPS3:WDTPD0
Name
All Device Resets
INTRC Oscillator
Watchdog Timer (WDT)
SWDTEN
CLRWDT
bit 7-1
bit 0
Sleep
IPEN
Bit 7
SUMMARY OF WATCHDOG TIMER REGISTERS
—
WDT BLOCK DIAGRAM
WDTCON: WATCHDOG TIMER CONTROL REGISTER
bit 7
Unimplemented: Read as ‘0’
SWDTEN: Software Controlled Watchdog Timer Enable bit
1 = Watchdog Timer is on
0 = Watchdog Timer is off
Legend:
R = Readable bit
-n = Value at POR
Note 1: This bit has no effect if the configuration bit, WDTEN, is enabled.
U-0
—
Bit 6
Enable WDT
—
—
U-0
WDT Counter
—
Bit 5
—
—
÷128
INTRC Control
4
U-0
Bit 4
—
Preliminary
Programmable Postscaler
RI
—
W = Writable bit
‘1’ = Bit is set
1:1 to 1:32,768
U-0
Bit 3
PIC18F45J10 FAMILY
—
TO
—
20.2.1
The WDTCON register (Register 20-9) is a readable
and writable register. The SWDTEN bit enables or
disables WDT operation.
Note 1: The CLRWDT and SLEEP instructions
Bit 2
2: When a CLRWDT instruction is executed,
U-0
PD
WDT
—
—
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
CONTROL REGISTER
clear the WDT and postscaler counts
when executed.
the postscaler count will be cleared.
Reset
(1)
Bit 1
POR
—
U-0
—
SWDTEN
Bit 0
BOR
x = Bit is unknown
U-0
—
DS39682B-page 235
Wake-up from
Power-Managed
Modes
WDT
Reset
Reset Values
SWDTEN
on page
R/W-0
44
44
bit 0
(1)