ST92T163R4T1 STMicroelectronics, ST92T163R4T1 Datasheet - Page 142

• Manufacturer Part Number: ST92T163R4T1
• Description: Microcontrollers (MCU) OTP EPROM 20K USB/I2
• Manufacturer: STMicroelectronics

Specifications of ST92T163R4T1

• Data Bus Width: 8 bit, 16 bit
• Program Memory Type: EPROM
• Program Memory Size: 20 KB
• Data Ram Size: 2 KB
• Interface Type: I2C, SCI, USB
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 64
• Number Of Timers: 2
• Operating Supply Voltage: 4 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Package / Case: TQFP-64
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8 bit
• Lead Free Status / Rohs Status: No

ST92163 - USB PERIPHERAL (USB)
USB INTERFACE (Cont’d)
CTR INTERRUPT FLAGS (CTRINF)
R253 - Read/Write
Register page: 15
Reset Value: 00xx xxx0 (xxh)
Note: This register is used only when the SDNAV
bit is 1.
Bit 7:6 = Reserved. These bits are fixed by hard-
ware at 0.
Bit 5 = INTO: Interrupt occurred .
Set by hardware when SDNAV = 1 in the same
way as the CTRO bit in USBIVR register is set
when SDNAV = 0.
Bit 4:1 = ENID[3:0]: Endpoint identifier .
Set by hardware when SDNAV = 1 in the same
way as V[3:0] bits in USBIVR register are set when
SDNAV = 0.
Bit 0 = Reserved. This bit is fixed by hardware at 0.
FRAME NUMBER REGISTER HIGH (FNRH)
R254 - Read-only
Register page: 15
Reset Value: 0000 0xxx (0xh)
Bit 7 = RXDP.
Set/cleared by hardware to indicate D+ upstream
port data line status.
Bit 6 = RXDM.
Set/cleared by hardware to indicate D- upstream
port data line status.
142/224
RXDP RXDM
7
0
7
0
INTO
LCK
LSOF1 LSOF0 FN10
ENID3 ENID2 ENID1 ENID0
FN9
FN8
0
0
0
Bit 5 = LCK: Locked .
Set by hardware when at least two consecutive
SOF packets have been received after the end of
a USB reset condition or after the end of a USB
resume sequence.
0: Frame timer not locked
1: Frame timer locked
Note: Once locked, the frame timer remains in this
state until a USB reset or USB suspend event oc-
curs.
Bits 4:3 = LSOF[1:0]: Lost SOF .
Set by hardware when an ESOF interrupt is gener-
ated, counting the number of consecutive SOF
packets lost. On reception of a SOF packet, these
bits are cleared.
Bits 2:0 = FN[10:8]: Frame Number bits 10:8 .
These bits contain the most significant bits of the
Frame number received with the last received
SOF packet. These bits are updated when a SOF
interrupt is generated.
FRAME NUMBER REGISTER LOW (FNRL)
R255 - Read-only
Register page: 15
Reset Value: xxxx xxxx (xxh)
Bits 7:0 = FN[7:0]: Frame Number bits 7:0 .
Set by hardware, this register contains the least
significant bits of the 11-bit frame number con-
tained in the last received SOF packet. The 3 re-
maining most significant bits are stored in the
FNRH register. This register is updated when a
SOF interrupt is generated.
8.3.4.2 Device and Endpoint specific Registers
For each function a DADDR register is available to
store the device address and for each endpoint a
pair of EPnR registers is available to store end-
point specific information.
FN7
7
FN6
FN5
FN4
FN3
FN2
FN1
FN0
0