P80C557E4EFB NXP Semiconductors, P80C557E4EFB Datasheet - Page 20
![](/photos/31/38/313843/sot318-2_sml.jpg)
P80C557E4EFB
Manufacturer Part Number
P80C557E4EFB
Description
Manufacturer
NXP Semiconductors
Datasheet
1.P80C557E4EFB.pdf
(72 pages)
Specifications of P80C557E4EFB
Cpu Family
80C
Device Core
80C51
Device Core Size
8b
Frequency (max)
16MHz
Interface Type
I2C/UART
Program Memory Type
ROMLess
Program Memory Size
Not Required
Total Internal Ram Size
1KB
# I/os (max)
40
Number Of Timers - General Purpose
3
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
4.5V
On-chip Adc
8-chx10-bit
Instruction Set Architecture
CISC
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
80
Package Type
PQFP
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P80C557E4EFB
Manufacturer:
PHILIPS
Quantity:
325
Part Number:
P80C557E4EFB
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
P80C557E4EFB/01
Manufacturer:
SAMSUNG
Quantity:
10 000
Company:
Part Number:
P80C557E4EFB/01,51
Manufacturer:
SILICON
Quantity:
459
Company:
Part Number:
P80C557E4EFB/01,51
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
P80C557E4EFB/01,55
Manufacturer:
IR
Quantity:
20
Company:
Part Number:
P80C557E4EFB/01,55
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
Digital Input Port Register P5
Port 5 Special Function Register P5 always represents the binary
value of the logic level at input pins P5.0/ADC0...P5.7/ADC7. P5 is
not affected by chip reset. P5 is a read only register. Its hardware
address is C7H. P5 is not bit addressable.
Reading Special Function Register P5 does not affect A/D
conversions. But it is recommended to use the digital input port
function of the hardware Port 5 only as an alternative to analog input
voltage conversions. Simultaneous mixed operation is discouraged
for the sake of A/D conversion result reliability and accuracy.
For further information on Port 5, refer to the “I/O facilities” section.
For further information on A/D Special Function Registers, refer to
the “Internal Data Memory” section.
Reset
After a RESET of the microcontroller the ADCON and ADPSS
register bits are initialized to zero. Registers ADRSLn and ADRSH
are not initialized by a RESET.
Idle and Power-down Mode
The A/D Converter is active only when the microcontroller is in
normal operating mode. If the Idle or Power-down Mode is activated,
then the ADC is switched off and put into a power saving idle state –
a conversion in progress is aborted, a previously set ADSST flag is
cleared and the internal clock is halted. The conversion result
registers are not affected.
The interrupt flag ADINT will not be set by activation of Idle or
Power-down Mode. A previously set flag ADINT will not be cleared
by the hardware. (Note: ADINT cannot be cleared by hardware at
all, except for a RESET – it must be cleared by the user software.)
After a wakeup from Idle or Power-down Mode a set flag ADINT
indicates that at least one autoscan loop was finished completely
before the microcontroller was put into the respective power
reduction mode and it indicates that the stored result data may be
fetched now – if desired.
For further information on Idle and Power-down Mode, refer to the
“Power reduction modes” section.
Timing
A programmable prescaler is controlled by the bits ADPR1 and
ADPR0 in register ADCON to adapt the conversion time for different
microcontroller clock frequencies.
Table 11 shows conversion times (tconv) for one A/D conversion at
some convenient system clock frequencies (fclk) and ADC prescaler
divisors (m), which are user selectable by the bits ADCON.7/ADPR1
and ADCON.6/ADPR0.
1999 Mar 02
Single-chip 8-bit microcontroller
P5 (C7H)
P5.7
7
P5.6
6
Figure 18. Digital input port register P5.
P5.5
5
20
P5.4
4
P83C557E4/P80C557E4/P89C557E4
Conversion time tconv = (6 m + 1) machine cycles
For conversion times outside the limits for tconv the specified ADC
characteristics are not guaranteed; (prohibited conversion times are
put in brackets):
Table 11. Conversion time configuration
A conversion time tconv consists of one sample time period (which
equals two bit conversion times), 10 bit conversion time periods and
one machine cycle to store the result.
After result storage an extra initializing time period follows to select
the next analog input channel (according to the contents of SFR
ADPSS), before the input signal is sampled.
Thus the time period between two adjacent conversions within an
autoscan loop is larger than the pure time tconv. This autoscan cycle
time is ( 7 m ) machine cycles.
At the start of an autoscan conversion the time between writing to
SFR ADCON and the first analog input signal sampling depends on
the current prescaler value (m) and the relative time offset between
this write operation and the internal (divided) ADC clock. This gives
a variation range for the A/D conversion start time of ( m / 2 )
machine cycles.
m
2
4
6
8
P5.3
examples (tconv/ s)
3
6 MHz
[74]
[98]
26
50
P5.2
2
8 MHz
[55.5]
[73.5]
19.5
37.5
f
CLK
P5.1
1
12 MHz
[13]
25
37
49
Product specification
P5.0
0
16 MHz
[9.75]
18.75
27.75
36.75