AT32UC3C1128C Atmel Corporation, AT32UC3C1128C Datasheet - Page 24

• Manufacturer Part Number: AT32UC3C1128C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C1128C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 81
• Ext Interrupts: 100
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 19
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Table 3-7.
3.4
3.4.1
3.4.2
3.4.3
3.4.4
32117C–AVR-08/11
Signal Name
DP
VBUS
ID
VBOF
I/O Line Considerations
JTAG pins
RESET_N pin
TWI pins
GPIO pins
Signal Description List
Function
USB Device Port Data +
USB VBUS Monitor and OTG Negociation
ID Pin of the USB Bus
USB VBUS On/off: bus power control port
The JTAG is enabled if TCK is low while the RESET_N pin is released. The TCK, TMS, and TDI
pins have pull-up resistors when JTAG is enabled. The TCK pin always have pull-up enabled
during reset. The TDO pin is an output, driven at VDDIO1, and has no pull-up resistor. The
JTAG pins can be used as GPIO pins and muxed with peripherals when the JTAG is disabled.
Please refer to
The RESET_N pin integrates a pull-up resistor to VDDIO1. As the product integrates a power-on
reset cell, the RESET_N pin can be left unconnected in case no reset from the system needs to
be applied to the product.
The RESET_N pin is also used for the aWire debug protocol. When the pin is used for debug-
ging, it must not be driven by external circuitry.
When these pins are used for TWI, the pins are open-drain outputs with slew-rate limitation and
inputs with inputs with spike-filtering. When used as GPIO-pins or used for other peripherals, the
pins have the same characteristics as GPIO pins.
All I/O lines integrate programmable pull-up and pull-down resistors. Most I/O lines integrate
drive strength control, see
drive strength is performed independently for each I/O line through the GPIO Controllers.
After reset, I/O lines default as inputs with pull-up/pull-down resistors disabled. After reset, out-
put drive strength is configured to the lowest value to reduce global EMI of the device.
When the I/O line is configured as analog function (ADC I/O, AC inputs, DAC I/O), the pull-up
and pull-down resistors are automatically disabled.
Section 3.2.4
Table
for the JTAG port connections.
3-1. Programming of this pull-up and pull-down resistor or this
Analog
Analog
output
Type
Input
Input
Active
Level
Comments
AT32UC3C
24