AT32UC3C1128C Atmel Corporation, AT32UC3C1128C Datasheet - Page 635

• Manufacturer Part Number: AT32UC3C1128C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C1128C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 81
• Ext Interrupts: 100
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 19
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
32117C–AVR-08/11
DCD: Image of DCD Input
DSR: Image of DSR Input
RI: Image of RI Input
CTSIC: Clear to Send Input Change Flag
DCDIC: Data Carrier Detect Input Change Flag
DSRIC: Data Set Ready Input Change Flag
RIIC: Ring Indicator Input Change Flag
LINTC: LIN Transfer Completed
LINID: LIN Identifier
NACK: Non Acknowledge
RXBUFF: Reception Buffer Full
ITER/UNRE: Max number of Repetitions Reached or SPI Underrun Error
TXEMPTY: Transmitter Empty
TIMEOUT: Receiver Time-out
PARE: Parity Error
0: LIN Bus Line is at 0.
1: LIN Bus Line is at 1.
0: DCD is at 0.
1: DCD is at 1.
0: DSR is at 0.
1: DSR is at 1.
0: RI is at 0.
1: RI is at 1.
0: No input change has been detected on the CTS pin since the last read of CSR.
1: At least one input change has been detected on the CTS pin since the last read of CSR.
0: No input change has been detected on the DCD pin since the last read of CSR.
1: At least one input change has been detected on the DCD pin since the last read of CSR.
0: No input change has been detected on the DSR pin since the last read of CSR.
1: At least one input change has been detected on the DSR pin since the last read of CSR.
0: No input change has been detected on the RI pin since the last read of CSR.
1: At least one input change has been detected on the RI pin since the last read of CSR.
0: The USART is idle or a LIN transfer is ongoing.
1: A LIN transfer has been completed since the last RSTSTA.
0: No LIN Identifier received or sent
1: The USART is configured as a Slave node and a LIN Identifier has been received or the USART is configured as a Master
0: No Non Acknowledge has not been detected since the last RSTNACK.
1: At least one Non Acknowledge has been detected since the last RSTNACK.
0: The signal Buffer Full from the Receive Peripheral DMA Controller channel is inactive.
1: The signal Buffer Full from the Receive Peripheral DMA Controller channel is active.
If USART does not operate in SPI Slave Mode (MODE … 0xF):
ITER = 0: Maximum number of repetitions has not been reached since the last RSTSTA.
ITER = 1: Maximum number of repetitions has been reached since the last RSTSTA.
If USART operates in SPI Slave Mode (MODE = 0xF):
UNRE = 0: No SPI underrun error has occurred since the last RSTSTA.
UNRE = 1: At least one SPI underrun error has occurred since the last RSTSTA.
0: There are characters in either THR or the Transmit Shift Register, or the transmitter is disabled.
1: There are no characters in THR, nor in the Transmit Shift Register.
0: There has not been a time-out since the last Start Time-out command (STTTO in CR) or the Time-out Register is 0.
1: There has been a time-out since the last Start Time-out command (STTTO in CR).
node and a LIN Identifier has been sent since the last RSTSTA.
AT32UC3C
635