AT32UC3C1128C Atmel Corporation, AT32UC3C1128C Datasheet - Page 753

• Manufacturer Part Number: AT32UC3C1128C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C1128C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 81
• Ext Interrupts: 100
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 19
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

• SMBPECERR: SMBus PEC Error
• SMBTOUT: SMBus Timeout
• NAK: NAK Received
• ORUN: Overrun
• URUN: Underrun
• TRA: Transmitter Mode
• TCOMP: Transmission Complete
• SEN: Slave Enabled
• TXRDY: TX Buffer Ready
• RXRDY: RX Buffer Ready
32117C–AVR-08/11
This bit is cleared when the corresponding bit in SCR is written to one.
This bit is set when a SMBus PEC error has occurred.
This bit is cleared when the corresponding bit in SCR is written to one.
This bit is set when a SMBus timeout has occurred.
This bit is cleared when the corresponding bit in SCR is written to one.
This bit is set when a NAK was received from the master during slave transmitter operation.
This bit is cleared when the corresponding bit in SCR is written to one.
This bit is set when an overrun has occurred in slave receiver mode. Can only occur if CR.STREN is zero.
This bit is cleared when the corresponding bit in SCR is written to one.
This bit is set when an underrun has occurred in slave transmitter mode. Can only occur if CR.STREN is zero.
0: The slave is in slave receiver mode.
1: The slave is in slave transmitter mode.
This bit is cleared when the corresponding bit in SCR is written to one.
This bit is set when transmission is complete. Set after receiving a STOP after being addressed.
0: The slave interface is disabled.
1: The slave interface is enabled.
0: The TX buffer is full and should not be written to.
1: The TX buffer is empty, and can accept new data.
0: No RX data ready in RHR.
1: RX data is ready to be read from RHR.
AT32UC3C
753