AT32UC3C1128C Atmel Corporation, AT32UC3C1128C Datasheet - Page 872

• Manufacturer Part Number: AT32UC3C1128C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C1128C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 81
• Ext Interrupts: 100
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 19
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32.5
32.5.1
32.5.2
32.5.3
32.5.4
32117C–AVR-08/11
Product Dependencies
I/O Lines
Power Management
Clocks
Interrupts
In order to use this module, other parts of the system must be configured correctly, as described
below.
The USBC pins may be multiplexed with the I/O Controller lines. The user must first configure
the I/O Controller to assign the desired USBC pins to their peripheral functions.
If the USB_ID pin is used the user must also enable its internal pull-up resistor.
If the CPU enters a sleep mode that disables clocks used by the USBC, the USBC will stop func-
tioning and resume operation after the system wakes up from sleep mode.
The USBC has two bus clocks connected: One High Speed Bus clock (CLK_USBC_HSB) and
one Peripheral Bus clock (CLK_USBC_PB). These clocks are generated by the Power Man-
ager. Both clocks are enabled at reset, and can be disabled by the Power Manager. It is
recommended to disable the USBC before disabling the clocks, to avoid freezing the USBC in
an undefined state.
The 48MHz USB clock is generated by a dedicated generic clock from the SCIF module. Before
using the USB, the user must ensure that the USB generic clock (GCLK_USBC) is enabled at
48MHz in the SCIF module.
The USBC interrupt request line is connected to the interrupt controller. Using the USBC inter-
rupt requires the interrupt controller to be programmed first.
The USBC asynchronous interrupts can wake the CPU from any sleep mode:
• The ID Transition Interrupt (IDTI)
• The VBUS Transition Interrupt (VBUSTI) if the bandgap voltage reference is ON (Refer to the
• The Wakeup Interrupt (WAKEUP)
• The Host Wakeup Interrupt (HWUPI)
Power Manager chapter)
AT32UC3C
872