AT32UC3C2256C Atmel Corporation, AT32UC3C2256C Datasheet - Page 663

• Manufacturer Part Number: AT32UC3C2256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C2256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 45
• Ext Interrupts: 64
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 13
• Input Capture Channels: 6
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

26.7.3.3
26.7.3.4
Figure 26-7. Programmable Delays
32117C–AVR-08/11
Chip Select 1
Chip Select 2
Clock generation
Transfer delays
SPCK
The SPI Baud rate clock is generated by dividing the CLK_SPI , by a value between 1 and 255.
This allows a maximum operating baud rate at up to CLK_SPI and a minimum operating baud
rate of CLK_SPI divided by 255.
Writing the Serial Clock Baud Rate field in the CSRn registers (CSRn.SCBR) to zero is forbid-
den. Triggering a transfer while CSRn.SCBR is zero can lead to unpredictable results.
At reset, CSRn.SCBR is zero and the user has to configure it at a valid value before performing
the first transfer.
The divisor can be defined independently for each chip select, as it has to be configured in the
CSRn.SCBR field. This allows the SPI to automatically adapt the baud rate for each interfaced
peripheral without reprogramming.
Figure 26-7 on page 663
same chip select. Three delays can be configured to modify the transfer waveforms:
These delays allow the SPI to be adapted to the interfaced peripherals and their speed and bus
release time.
• The delay between chip selects, programmable only once for all the chip selects by writing to
• The delay before SPCK, independently programmable for each chip select by writing the
• The delay between consecutive transfers, independently programmable for each chip select
the Delay Between Chip Selects field in the MR register (MR.DLYBCS). Allows insertion of a
delay between release of one chip select and before assertion of a new one.
Delay Before SPCK field in the CSRn registers (CSRn.DLYBS). Allows the start of SPCK to
be delayed after the chip select has been asserted.
by writing the Delay Between Consecutive Transfers field in the CSRn registers
(CSRn.DLYBCT). Allows insertion of a delay between two transfers occurring on the same
chip select
DLYBCS
DLYBS
shows a chip select transfer change and consecutive transfers on the
DLYBCT
AT32UC3C
DLYBCT
663