AT32UC3C2256C Atmel Corporation, AT32UC3C2256C Datasheet - Page 707

• Manufacturer Part Number: AT32UC3C2256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C2256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 45
• Ext Interrupts: 64
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 13
• Input Capture Channels: 6
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 27-11. Arbitration Cases
27.8.7
27.8.7.1
32117C–AVR-08/11
Data from a Master
TWI DATA transfer
Data from TWI
(DADR + W + START + Write THR)
Combined Transfers
ARBLST
A transfer is programmed
TWCK
Write Followed by Write
TWD
TWCK
TWD
CMDR and NCMDR may be used to generate longer sequences of connected transfers, since
generation of START and/or STOP conditions is programmable on a per-command basis.
Writing NCMDR with START=1 when the previous transfer was written with STOP=0 will cause
a REPEATED START on the bus. The ability to generate such connected transfers allows arbi-
trary transfer lengths, since it is legal to write CMDR with both START=0 and STOP=0. If this is
done in master receiver mode, the CMDR.ACKLAST bit must also be controlled.
As for single data transfers, the TXRDY and RXRDY bits in the Status Register indicates when
data to transmit can be written to THR, or when received data can be read from RHR. Transfer
of data to THR and from RHR can also be done automatically by DMA, see
Consider the following transfer:
START, DADR+W, DATA+A, DATA+A, REPSTART, DADR+W, DATA+A, DATA+A, STOP.
To generate this transfer:
1. Write CMDR with START=1, STOP=0, DADR, NBYTES=2 and READ=0.
2. Write NCMDR with START=1, STOP=1, DADR, NBYTES=2 and READ=0.
3. Wait until SR.TXRDY==1, then write first data byte to transfer to THR.
4. Wait until SR.TXRDY==1, then write second data byte to transfer to THR.
5. Wait until SR.TXRDY==1, then write third data byte to transfer to THR.
S
S
S
1
1
1
Transfer is stopped
0 0
0
0 0
1
1 1
1 1
TWI stops sending data
Arbitration is lost
(DADR + W + START + Write THR)
Transfer is programmed again
Data from the master
Bus is busy
Transfer is kept
P
P
Bus is free
Bus is considered as free
Transfer is initiated
S
S
S
1
1
1
0
0 0
0
1
0
1 1
The master stops sending data
1 1
Arbitration is lost
AT32UC3C
Section 27.8.5
Data from the TWI
707