AT90CAN64 Atmel Corporation, AT90CAN64 Datasheet - Page 43
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT90CAN64
Manufacturer Part Number
AT90CAN64
Description
Manufacturer
Atmel Corporation
Specifications of AT90CAN64
Flash (kbytes)
64 Kbytes
Pin Count
64
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
53
Ext Interrupts
8
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Uart
2
Can
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
4
Eeprom (bytes)
2048
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
8
Input Capture Channels
2
Pwm Channels
7
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT90CAN64-15AT
Manufacturer:
Atmel
Quantity:
3 327
Company:
Part Number:
AT90CAN64-15AT1
Manufacturer:
Atmel
Quantity:
1 985
Company:
Part Number:
AT90CAN64-15AZ
Manufacturer:
Atmel
Quantity:
1 995
Company:
Part Number:
AT90CAN64-15MT
Manufacturer:
Freescale
Quantity:
100
Company:
Part Number:
AT90CAN64-15MT1
Manufacturer:
Atmel
Quantity:
7 775
Part Number:
AT90CAN64-15MT1
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
AT90CAN64-16AU
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
AT90CAN64-16MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
5.8
5.9
7679H–CAN–08/08
Clock Output Buffer
Timer/Counter2 Oscillator
Figure 5-4.
Table 5-10.
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 5-11.
When applying an external clock, it is required to avoid sudden changes in the applied clock fre-
quency to ensure stable operation of the MCU. A variation in frequency of more than 2% from
one clock cycle to the next can lead to unpredictable behavior. It is required to ensure that the
MCU is kept in Reset during such changes in the clock frequency.
Note that the System Clock Prescaler can be used to implement run-time changes of the internal
clock frequency while still ensuring stable operation. Refer to
44
When the CKOUT Fuse is programmed, the system Clock will be output on CLKO. This mode is
suitable when chip clock is used to drive other circuits on the system. The clock will be output
also during reset and the normal operation of I/O pin will be overridden when the fuse is pro-
grammed. Any clock source, including internal RC Oscillator, can be selected when CLKO
serves as clock output. If the System Clock Prescaler is used, it is the divided system clock that
is output (CKOUT Fuse programmed).
For AVR microcontrollers with Timer/Counter2 Oscillator pins (TOSC1 and TOSC2), the crystal
is connected directly between the pins. The Oscillator is optimized for use with a 32.768 kHz
watch crystal. 12-22 pF capacitors may be necessary if the parasitic impedance (pads, wires &
PCB) is very low.
CKSEL3..0
0000
SUT1..0
for details.
00
01
10
11
5-11.
Start-up Time from Power-
External Clock Drive Configuration
External Clock Frequency
Start-up Times for the External Clock Selection
down and Power-save
6 CK
6 CK
6 CK
External
Signal
Clock
Frequency Range
0 - 16 MHz
NC
Additional Delay from
Reset (V
Reserved
14 CK + 4.1 ms
14 CK + 65 ms
14 CK
CC
= 5.0V)
AT90CAN32/64/128
“System Clock Prescaler” on page
XTAL2
XTAL1
GND
BOD enabled
Fast rising power
Slowly rising power
Recommended Usage
43