AT90CAN64 Atmel Corporation, AT90CAN64 Datasheet - Page 70
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT90CAN64
Manufacturer Part Number
AT90CAN64
Description
Manufacturer
Atmel Corporation
Specifications of AT90CAN64
Flash (kbytes)
64 Kbytes
Pin Count
64
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
53
Ext Interrupts
8
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Uart
2
Can
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
4
Eeprom (bytes)
2048
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
8
Input Capture Channels
2
Pwm Channels
7
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT90CAN64-15AT
Manufacturer:
Atmel
Quantity:
3 327
Company:
Part Number:
AT90CAN64-15AT1
Manufacturer:
Atmel
Quantity:
1 985
Company:
Part Number:
AT90CAN64-15AZ
Manufacturer:
Atmel
Quantity:
1 995
Company:
Part Number:
AT90CAN64-15MT
Manufacturer:
Freescale
Quantity:
100
Company:
Part Number:
AT90CAN64-15MT1
Manufacturer:
Atmel
Quantity:
7 775
Part Number:
AT90CAN64-15MT1
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
AT90CAN64-16AU
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
AT90CAN64-16MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
9.2.5
70
AT90CAN32/64/128
Digital Input Enable and Sleep Modes
The following code example shows how to set port B pins 0 and 1 high, 2 and 3 low, and define
the port pins from 4 to 7 as input with pull-ups assigned to port pins 6 and 7. The resulting pin
values are read back again, but as previously discussed, a nop instruction is included to be able
to read back the value recently assigned to some of the pins.
Note:
As shown in
schmitt-trigger. The signal denoted SLEEP in the figure, is set by the MCU Sleep Controller in
Power-down mode, Power-save mode, and Standby mode to avoid high power consumption if
some input signals are left floating, or have an analog signal level close to V
SLEEP is overridden for port pins enabled as external interrupt pins. If the external interrupt
request is not enabled, SLEEP is active also for these pins. SLEEP is also overridden by various
other alternate functions as described in
If a logic high level (“one”) is present on an Asynchronous External Interrupt pin configured as
“Interrupt on Rising Edge, Falling Edge, or Any Logic Change on Pin” while the external interrupt
is not enabled, the corresponding External Interrupt Flag will be set when resuming from the
Assembly Code Example
C Code Example
unsigned char i;
...
; Define pull-ups and set outputs high
; Define directions for port pins
ldi
ldi
out
out
; Insert nop for synchronization
nop
; Read port pins
in
...
...
/* Define pull-ups and set outputs high */
/* Define directions for port pins */
PORTB = (1<<PB7)|(1<<PB6)|(1<<PB1)|(1<<PB0);
DDRB = (1<<DDB3)|(1<<DDB2)|(1<<DDB1)|(1<<DDB0);
/* Insert nop for synchronization*/
_NOP();
/* Read port pins */
i = PINB;
...
1. For the assembly program, two temporary registers are used to minimize the time from pull-
ups are set on pins 0, 1, 6, and 7, until the direction bits are correctly set, defining bit 2 and 3
as low and redefining bits 0 and 1 as strong high drivers.
Figure
r16, (1<<PB7)|(1<<PB6)|(1<<PB1)|(1<<PB0)
r17, (1<<DDB3)|(1<<DDB2)|(1<<DDB1)|(1<<DDB0)
PORTB, r16
DDRB, r17
r16, PINB
(1)
9-2, the digital input signal can be clamped to ground at the input of the
(1)
“Alternate Port Functions” on page
CC
71.
/2.
7679H–CAN–08/08