ATmega16U4 Atmel Corporation, ATmega16U4 Datasheet - Page 33
ATmega16U4
Manufacturer Part Number
ATmega16U4
Description
Manufacturer
Atmel Corporation
Specifications of ATmega16U4
Flash (kbytes)
16 Kbytes
Pin Count
44
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
14
Hardware Qtouch Acquisition
No
Max I/o Pins
26
Ext Interrupts
13
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
12
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
2.1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
12
Input Capture Channels
2
Pwm Channels
8
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 33 of 433
- Download datasheet (9Mb)
6.5.2
6.6
7766F–AVR–11/10
External Clock
Oscillator Control Register – RCCTRL
The temperature sensitivity is quite linear but as said previously depends on the process. To
determine its slope, the frequency must be measured at two temperatures. The temperature
sensor of the ATmega16U4/ATmega32U4 allows such an operation, that is detailed on
24.6.1 ”Sensor Calibration” on page
in function of the temperature measured.
Note that this oscillator is used to time EEPROM and Flash write accesses, and these write
times will be affected accordingly. If the EEPROM or Flash are written, do not calibrate to more
than 8.8 MHz. Otherwise, the EEPROM or Flash write may fail.
Bits 7..1 – Reserved
Do not set these bits. Bits should be read as ‘0’.
Bit 0– RCFREQ: RC Oscillator Frequency Select
When this bit is cleared (default value), the RC Oscillator output frequency is set to 8 MHz.
When the bit is set, the RC output frequency is 1 MHz. Note that the OSCCAL value has the
same effect on both 8 MHz and 1 MHz output modes (~0.4% / step).
The device can utilize a external clock source as shown in
external clock, the CKSEL Fuses must be programmed as shown in
Figure 6-3.
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table
Bit
Read/Write
Initial Value
6-9.
7
-
R
0
External Clock Drive Configuration
6
-
R
0
EXTERNAL
SIGNAL
CLOCK
5
-
R
0
NC
300. It is then possible to calibrate the oscillator frequency
4
-
R
0
3
-
R
0
XTAL2
XTAL1
GND
2
-
R
0
Figure
1
-
R
0
ATmega16/32U4
6-3. To run the device on an
Table
0
RCFREQ
R/W
0
6-1.
RCCTRL
Section
33
Related parts for ATmega16U4
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: