SAM3U2E Atmel Corporation, SAM3U2E Datasheet - Page 895

• Manufacturer Part Number: SAM3U2E
• Manufacturer: Atmel Corporation

Specifications of SAM3U2E

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 57
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 5
• Twi (i2c): 2
• Uart: 5
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

38.6.5
38.6.5.1
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11
PWM Controller Operations
Initialization
Before enabling the channels, they must have been configured by the software application:
• Unlock User Interface by writing the WPCMD field in the PWM_WPCR Register.
• Configuration of the clock generator (DIVA, PREA, DIVB, PREB in the PWM_CLK register if
• Selection of the clock for each channel (CPRE field in the PWM_CMRx register)
• Configuration of the waveform alignment for each channel (CALG field in the PWM_CMRx
• Selection of the counter event selection (if CALG = 1) for each channel (CES field in the
• Configuration of the output waveform polarity for each channel (CPOL in the PWM_CMRx
• Configuration of the period for each channel (CPRD in the PWM_CPRDx register). Writing in
• Configuration of the duty-cycle for each channel (CDTY in the PWM_CDTYx register).
• Configuration of the dead-time generator for each channel (DTH and DTL in PWM_DTx) if
• Selection of the synchronous channels (SYNCx in the PWM_SCM register)
• Selection of the moment when the WRDY flag and the corresponding PDC transfer request
• Configuration of the update mode (UPDM in the PWM_SCM register)
• Configuration of the update period (UPR in the PWM_SCUP register) if needed.
• Configuration of the comparisons (PWM_CMPVx and PWM_CMPMx).
• Configuration of the event lines (PWM_ELMRx).
• Configuration of the fault inputs polarity (FPOL in PWM_FMR)
• Configuration of the fault protection (FMOD and FFIL in PWM_FMR, PWM_FPV and
• Enable of the Interrupts (writing CHIDx and FCHIDx in PWM_IER1 register, and writing
• Enable of the PWM channels (writing CHIDx in the PWM_ENA register)
required).
register)
PWM_CMRx register)
register)
PWM_CPRDx register is possible while the channel is disabled. After validation of the
channel, the user must use PWM_CPRDUPDx register to update PWM_CPRDx as
explained below.
Writing in PWM_CDTYx register is possible while the channel is disabled. After validation of
the channel, the user must use PWM_CDTYUPDx register to update PWM_CDTYx as
explained below.
enabled (DTE bit in the PWM_CMRx register). Writing in the PWM_DTx register is possible
while the channel is disabled. After validation of the channel, the user must use
PWM_DTUPDx register to update PWM_DTx
are set (PTRM and PTRCS in the PWM_SCM register)
PWM_FPE1)
WRDYE, ENDTXE, TXBUFE, UNRE, CMPMx and CMPUx in PWM_IER2 register)
SAM3U Series
SAM3U Series
895
895