SAM4S16C Atmel Corporation, SAM4S16C Datasheet - Page 1027

• Manufacturer Part Number: SAM4S16C
• Manufacturer: Atmel Corporation

Specifications of SAM4S16C

• Flash (kbytes): 1024 Kbytes
• Pin Count: 100
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

39. Analog-to-Digital Converter (ADC)
39.1
39.2
11100A–ATARM–28-Oct-11
11100A–ATARM–28-Oct-11
Description
Embedded Characteristics
The ADC is based on a 12-bit Analog-to-Digital Converter (ADC) managed by an ADC Control-
ler. Refer to the Block Diagram:
making possible the analog-to-digital conversions of 16 analog lines. The conversions extend
from 0V to ADVREF. The ADC supports an 10-bit or 12-bit resolution mode, and conversion
results are reported in a common register for all channels, as well as in a channel-dedicated reg-
ister. Software trigger, external trigger on rising edge of the ADTRG pin or internal triggers from
Timer Counter output(s) are configurable.
The comparison circuitry allows automatic detection of values below a threshold, higher than a
threshold, in a given range or outside the range, thresholds and ranges being fully configurable.
The ADC Controller internal fault output is directly connected to PWM Fault input. This input can
be asserted by means of comparison circuitry in order to immediately put the PWM outputs in a
safe state (pure combinational path).
The ADC also integrates a Sleep Mode and a conversion sequencer and connects with a PDC
channel. These features reduce both power consumption and processor intervention.
This ADC has a selectable single-ended or fully differential input and benefits from a 2-bit pro-
grammable gain. A whole set of reference voltages is generated internally from a single external
reference voltage node that may be equal to the analog supply voltage. An external decoupling
capacitance is required for noise filtering.
A digital error correction circuit based on the multi-bit redundant signed digit (RSD) algorithm is
employed in order to reduce INL and DNL errors.
Finally, the user can configure ADC timings, such as Startup Time and Tracking Time.
• up to 16 Channels, 12-bit ADC
• 10/12-bit resolution
• up to 1 MSample/s
• Programmable conversion sequence conversion on each channel
• Integrated temperature sensor
• Automatic calibration mode
• Single ended/differential conversion
• Programmable gain: 1, 2, 4
Figure
39-1. It also integrates a 16-to-1 analog multiplexer,
SAM4S
SAM4S
1027
1027