SAM9G20 Atmel Corporation, SAM9G20 Datasheet - Page 170
SAM9G20
Manufacturer Part Number
SAM9G20
Description
Manufacturer
Atmel Corporation
Datasheets
1.SAM9261.pdf
(248 pages)
2.SAM9261.pdf
(1274 pages)
3.SAM9261.pdf
(43 pages)
4.SAM9G20.pdf
(42 pages)
5.SAM9G20.pdf
(832 pages)
Specifications of SAM9G20
Flash (kbytes)
0 Kbytes
Pin Count
217
Max. Operating Frequency
400 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
96
Ext Interrupts
96
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
1
Uart
7
Ssc
1
Ethernet
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
Yes
Adc Channels
4
Adc Resolution (bits)
10
Adc Speed (ksps)
95
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
NO
External Bus Interface
1
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
0.9 to 1.1
Fpu
No
Mpu / Mmu
No/Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- SAM9261 PDF datasheet
- SAM9261 PDF datasheet #2
- SAM9261 PDF datasheet #3
- SAM9G20 PDF datasheet #4
- SAM9G20 PDF datasheet #5
- Current page: 170 of 832
- Download datasheet (13Mb)
21.8.3
21.8.3.1
21.8.3.2
170
AT91SAM9G20
Write Waveforms
NWE Waveforms
NCS Waveforms
The write protocol is similar to the read protocol. It is depicted in
starts with the address setting on the memory address bus.
The NWE signal is characterized by a setup timing, a pulse width and a hold timing.
The NWE waveforms apply to all byte-write lines in Byte Write access mode: NWR0 to NWR3.
The NCS signal waveforms in write operation are not the same that those applied in read opera-
tions, but are separately defined:
Figure 21-12. Write Cycle
1. NWE_SETUP: the NWE setup time is defined as the setup of address and data before
2. NWE_PULSE: The NWE pulse length is the time between NWE falling edge and NWE
3. NWE_HOLD: The NWE hold time is defined as the hold time of address and data after
1. NCS_WR_SETUP: the NCS setup time is defined as the setup time of address before
2. NCS_WR_PULSE: the NCS pulse length is the time between NCS falling edge and
3. NCS_WR_HOLD: the NCS hold time is defined as the hold time of address after the
NBS0, NBS1,
NBS2, NBS3,
A0, A1
the NWE falling edge;
rising edge;
the NWE rising edge.
the NCS falling edge.
NCS rising edge;
NCS rising edge.
A
[25:2]
MCK
NWE
NCS
NCS_WR_SETUP
NWE_SETUP
NCS_WR_PULSE
NWE_CYCLE
NWE_PULSE
NWE_HOLD
Figure
NCS_WR_HOLD
21-12. The write cycle
6384E–ATARM–05-Feb-10
Related parts for SAM9G20
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: