TMP86xy49UG/F/NG Toshiba, TMP86xy49UG/F/NG Datasheet - Page 117

• Manufacturer Part Number: TMP86xy49UG/F/NG
• Manufacturer: Toshiba

Specifications of TMP86xy49UG/F/NG

• Package: LQFP64/QFP64/SDIP64
• Rom Types (m=mask,p=otp,f=flash): M/P/F
• Rom Size: 16/32/60
• Ram Size: 512/1K/2K
• Driver Led: 13
• Driver Lcd: -
• Spi/sio Channels: 2
• Uart/sio Channels: 2
• I2c/sio Channels: 1
• High-speed Serial Output: -
• Adc 8-bit Channels: -
• Adc 10-bit Channels: 16
• Da Converter Channels: -
• Timer Counter 18-bit Channel: -
• Timer Counter 16-bit Channel: 2
• Timer Counter 8-bit Channel: 4
• Motor Channels: -
• Watchdog Timer: Y
• Dual Clock: Y
• Clock Gear: -
• Number Of I/o Ports: 56
• Power Supply (v): 4.5 to 5.5

10.1 Configuration
10.2 TimerCounter Control
TimerCounter 3 Timer Register
TimerCounter 3 Control Register
PWREG3
TTREG3
(0014H)
(0018H)
(0027H)
TC3CR
(TTREG3, PWREG3).
R/W
R/W
The TimerCounter 3 is controlled by the TimerCounter 3 control register (TC3CR) and two 8-bit timer registers
Note 1: Do not change the timer register (TTREG3) setting while the timer is running.
Note 2: Do not change the timer register (PWREG3) setting in the operating mode except the 8-bit and 16-bit PWM modes while
Note 1: fc: High-frequency clock [Hz] fs: Low-frequency clock[Hz]
Note 2: Do not change the TC3M, TC3CK and TFF3 settings while the timer is running.
Note 3: To stop the timer operation (TC3S= 1 → 0), do not change the TC3M, TC3CK and TFF3 settings. To start the timer opera-
Note 4: To use the TimerCounter in the 16-bit mode, set the operating mode by programming TC4CR<TC4M>, where TC3M must
Note 5: To use the TimerCounter in the 16-bit mode, select the source clock by programming TC3CK. Set the timer start control
Note 6: The operating clock settings are limited depending on the timer operating mode. For the detailed descriptions, see Table
TC3CK
TC3M
TC3S
TFF3
the timer is running.
tion (TC3S= 0 → 1), TC3M, TC3CK and TFF3 can be programmed.
be fixed to 011.
and timer F/F control by programming TC4CR<TC4S> and TC4CR<TFF4>, respectively.
10-1 and Table 10-2.
TFF3
7
7
7
Time F/F3 control
Operating clock selection [Hz]
TC3 start control
TC3M operating mode select
6
6
6
TC3CK
5
5
5
4
4
4
000:
001:
010:
011:
1**:
TC3S
0:
1:
0:
1:
3
3
3
000
001
010
100
101
011
110
111
Clear
Set
Operation stop and counter clear
Operation start
8-bit timer/event counter mode
8-bit programmable divider output (PDO) mode
8-bit pulse width modulation (PWM) output mode
16-bit mode
(Each mode is selectable with TC4M.)
Reserved
2
2
2
Page 100
DV7CK = 0
TC3M
NORMAL1/2, IDLE1/2 mode
1
1
1
fc/2
fc/2
fc/2
fc/2
fc/2
fs
fc
11
7
5
3
0
0
0
(Initial value: 1111 1111)
(Initial value: 1111 1111)
(Initial value: 0000 0000)
TC3 pin input
DV7CK = 1
fs/2
fc/2
fc/2
fc/2
fc/2
fs
fc
3
7
5
3
fc (Note 8)
SLEEP1/2
SLOW1/2
mode
fs/2
fs
–
–
–
–
3
TMP86PM49UG
R/W
R/W
R/W
R/W