ST92185B STMicroelectronics, ST92185B Datasheet - Page 24
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
ST92185B
Manufacturer Part Number
ST92185B
Description
16k/24k/32k Rom Hcmos Mcu With On-screen-display
Manufacturer
STMicroelectronics
Datasheet
1.ST92185B.pdf
(178 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ST92185BJ2B1/0BE
Manufacturer:
ST
Quantity:
122
Company:
Part Number:
ST92185BN4B1/PBI
Manufacturer:
ST
Quantity:
35
ST92185B - DEVICE ARCHITECTURE
MEMORY SPACES (Cont’d)
2.2.2 Register Addressing
Register File registers, including Group F paged
registers (but excluding Group D), may be ad-
dressed explicitly by means of a decimal, hexa-
decimal or binary address; thus R231, RE7h and
R11100111b represent the same register (see
Figure
dressed in Working Register mode.
Note that an upper case “R” is used to denote this
direct addressing mode.
Working Registers
Certain types of instruction require that registers
be specified in the form “rx”, where x is in the
range 0 to 15: these are known as Working Regis-
ters.
Note that a lower case “r” is used to denote this in-
direct addressing mode.
Two addressing schemes are available: a single
group of 16 working registers, or two separately
mapped groups, each consisting of 8 working reg-
isters. These groups may be mapped starting at
any 8 or 16 byte boundary in the register file by
means of dedicated pointer registers. This tech-
nique is described in more detail in
and illustrated in
System Registers
The 16 registers in Group E (R224 to R239) are
System registers and may be addressed using any
of the register addressing modes. These registers
are described in greater detail in
Paged Registers
Up to 64 pages, each containing 16 registers, may
be mapped to Group F. These are addressed us-
ing any register addressing mode, in conjunction
with the Page Pointer register, R234, which is one
of the System registers. This register selects the
page to be mapped to Group F and, once set,
does not need to be changed if two or more regis-
ters on the same page are to be addressed in suc-
cession.
24/178
4). Group D registers can only be ad-
Figure 5
and in
Figure
Section
Section
6.
1.3.
1.3.3,
Therefore if the Page Pointer, R234, is set to 5, the
instructions:
spp #5
ld R242, r4
will load the contents of working register r4 into the
third register of page 5 (R242).
These paged registers hold data and control infor-
mation relating to the on-chip peripherals, each
peripheral always being associated with the same
pages and registers to ensure code compatibility
between ST9 devices. The number of these regis-
ters therefore depends on the peripherals which
are present in the specific ST9 family device. In
other words, pages only exist if the relevant pe-
ripheral is present.
Table 3. Register File Organization
Address
D0-DF
C0-CF
E0-EF
B0-BF
A0-AF
F0-FF
90-9F
80-8F
70-7F
60-6F
50-5F
40-4F
30-3F
20-2F
10-1F
00-0F
Hex.
Address
Decimal
240-255
224-239
208-223
192-207
176-191
160-175
144-159
128-143
112-127
96-111
80-95
64-79
48-63
32-47
16-31
00-15
Function
Registers
Registers
Registers
Purpose
General
System
Paged
File Group
Register
Group E
Group D
Group C
Group B
Group A
Group F
Group 9
Group 8
Group 7
Group 6
Group 5
Group 4
Group 3
Group 2
Group 1
Group 0