ST92185B STMicroelectronics, ST92185B Datasheet - Page 71
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
ST92185B
Manufacturer Part Number
ST92185B
Description
16k/24k/32k Rom Hcmos Mcu With On-screen-display
Manufacturer
STMicroelectronics
Datasheet
1.ST92185B.pdf
(178 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ST92185BJ2B1/0BE
Manufacturer:
ST
Quantity:
122
Company:
Part Number:
ST92185BN4B1/PBI
Manufacturer:
ST
Quantity:
35
INPUT/OUTPUT BIT CONFIGURATION (Cont’d)
When Px.n is programmed as an Output:
(Figure
– The Output Buffer is turned on in an Open-drain
– The data stored in the Output Master Latch is
When Px.n is programmed as Bidirectional:
(Figure
– The Output Buffer is turned on in an Open-Drain
– The data present on the I/O pin is sampled into
– The data stored in the Output Master Latch is
WARNING: Due to the fact that in bidirectional
mode the external pin is read instead of the output
latch, particular care must be taken with arithme-
tic/logic and Boolean instructions performed on a
bidirectional port pin.
These instructions use a read-modify-write se-
quence, and the result written in the port register
depends on the logical level present on the exter-
nal pin.
This may bring unwanted modifications to the port
output register content.
For example:
Port register content, 0Fh
external port value, 03h
(Bits 3 and 2 are externally forced to 0)
A bset instruction on bit 7 will return:
Port register content, 83h
external port value, 83h
(Bits 3 and 2 have been cleared).
To avoid this situation, it is suggested that all oper-
ations on a port, using at least one bit in bidirec-
tional mode, are performed on a copy of the port
register, then transferring the result with a load in-
struction to the I/O port.
When Px.n is programmed as a digital Alter-
nate Function Output:
(Figure
– The Output Buffer is turned on in an Open-Drain
or Push-pull configuration.
copied both into the Input Latch and into the Out-
put Slave Latch, driving the I/O pin, at the end of
the execution of the instruction.
or Weak Pull-up configuration (except when dis-
abled in hardware).
the Input Latch at the beginning of the execution
of the instruction.
copied into the Output Slave Latch, driving the I/
O pin, at the end of the execution of the instruc-
tion.
or Push-Pull configuration.
5)
6)
7)
– The data present on the I/O pin is sampled into
– The signal from an on-chip function is allowed to
Figure 41. Bidirectional Configuration
n
n
Figure 42. Alternate Function Configuration
n
n
n
n
n
n
the Input Latch at the beginning of the execution
of the instruction.
load the Output Slave Latch driving the I/O pin.
Signal timing is under control of the alternate
function. If no alternate function is connected to
Px.n, the I/O pin is driven to a high level when in
Push-Pull configuration, and to a high imped-
ance state when in open drain configuration.
WEAK PULL-UP
OPEN DRAIN
OPEN DRAIN
PUSH-PULL
PERIPHERAL
OUTPUT MASTER LATCH
OUTPUT SLAVE LATCH
OUTPUT
OUTPUT SLAVE LATCH
FROM
INTERNAL DATA BUS
INTERNAL DATA BUS
I/O PIN
I/O PIN
ST92185B - I/O PORTS
INPUT LATCH
INPUT LATCH
(or Schmitt Trigger)
(or Schmitt Trigger)
TO PERIPHERAL
INTERRUPTS
INPUTS AND
TO PERIPHERAL
INTERRUPTS
INPUTS AND
TTL
TTL
71/178