hsp50214 Intersil Corporation, hsp50214 Datasheet - Page 40

• Manufacturer Part Number: hsp50214
• Description: Programmable Downconverter
• Manufacturer: Intersil Corporation

Configuration Control Word Definitions
Note that in the Configuration Control Register tables some of
the available 32 bits in a control word are not used. Unused
bits do not need to be written to the master register. If the des-
tination only has 16 bits, then only 2 bytes need to be written
POSITION
31-21
16-13
12-7
BIT
5-4
20
19
18
17
6
3
2
1
0
CONTROL WORD 0: CHIP CONFIGURATION, INPUT SECTION, CIC GAIN (SYNCHRONOUS TO CLKIN)
Reserved
Carrier NCO External
Sync Enable
CIC External Sync
Enable
Input Format
Input Mode
CIC Shift Gain
CIC Counter Preload
CIC Bypassed
Number of Offset
Frequency Bits
Syncout CLK Select
Clear Phase Accum
Carrier NCO Offset
Frequency Enable
Carrier NCO Load
Phase Accum On
Update
FUNCTION
Reserved.
0- The SYNCIN1 pin has no effect on the Carrier NCO.
1- When the SYNCIN1 pin is asserted, the carrier center frequency and phase are updated from
the holding registers to the active register. Also, if bit 0 of this word is active, the carrier phase
accumulator feedback will be zeroed to set the Carrier NCO to a known phase, allowing the
NCOs of multiple parts to be initialized and updated synchronously.
0- The SYNCIN1 pin has no effect on the CIC filter.
1- When the SYNCIN1 pin is asserted, the decimation counter is loaded, allowing the decimation
counters in multiple chips to be synchronized.
0- Two’s Complement Input Format.
1- Offset Binary Input Format.
0- Input operates in Gated Mode.
1- Input operates in Interpolated Mode.
These bits control the barrel shifter at the input to the CIC filter. These bits are added to the
GAINADJ(2:0) pins to determine the total shift. The sum is saturated at 15. See the CIC Decima-
tion Filter Section for values to be programmed in this field based on CIC filter Decimation. Bit 16
is the MSB.
SG = Floor [39 - (number of input bits) - 5log
SG = 15 for R = 4.
SG = 0 for R = 32.
These bits control the decimation in the CIC filter. Program this field to
sired decimation rate in the filter. The decimation rate range is 4-32. See CIC Filter Section for
effective decimation range relative to the CIC Shift Gain value. Bit 12 is the MSB.
While this field allows values from 0 - 63, the valid values are in the range from 4- 32
Active high, this bit routes the output of the input shifter to the output of the CIC with no filtering.
When the CIC filter is bypassed, CLKIN must be at least twice the input sample rate (ENI should
be toggled to achieve this). When the CIC filter is bypassed, the bottom 24 bits of the barrel shifter
output are routed to the halfband filters.
00 - 8 bits.
01 - 16.
10 - 24.
11 - 32.
This bit selects whether the SYNCOUT signal is generated from CLKIN of from PROCCLK
0- CLKIN.
1- PROCLK.
0- Enable accumulator in Carrier NCO.
1- Zero feedback in accumulator.
When set to 1, this bit enables the offset frequency word to be added to the center frequency
control word. The offset is loaded serially via the COF and COFSYNC pins.
When this bit is set to 1, the P update to the Carrier NCO frequency or an external carrier NCO
load using SYNCIN1 will zero the feedback of the phase accumulator as well as update the phase
or frequency. This function can be used to set the NCO to a known phase synchronized to an
external event.
HSP50214
40
to the master register. Figure 39 details the timing for proper
operation of the Microprocessor Write Section. Bits identified
as “Reserved” should be programmed to a zero.
DESCRIPTION
2
(R)] for 4 < R < 31.
R-1
.
, where R is the de-