IDT72275 IDT [Integrated Device Technology], IDT72275 Datasheet - Page 3

• Manufacturer Part Number: IDT72275
• Manufacturer: IDT [Integrated Device Technology]

IDT72275/72285 SUPERSYNC FIFO™
32,768 x 18, 65,536 x 18
DESCRIPTION (Continued)
outputs of one FIFO are connected to the corresponding data
inputs of the next). No external logic is required.
Output Ready),
Flag),
grammable Almost-Full flag). The
selected in IDT Standard mode. The
selected in FWFT mode.
available for use, irrespective of timing mode.
at any point in memory. (See Table I and Table II.) Program-
mable offsets determine the flag switching threshold and can
be loaded by two methods: parallel or serial. Two default
offset settings are also provided, so that
switch at 127 or 1,023 locations from the empty boundary and
the
full boundary. These choices are made with the
Master Reset.
rising edge of WCLK, are used to load the offset registers via
the Serial Input (SI). For parallel programming,
with
offset registers via D
edge of RCLK can be used to read the offsets in parallel from
Q
been selected.
FIRST WORD FALL THROUGH/SERIAL INPUT
n
PAE
For serial programming,
These FIFOs have five flag pins,
regardless of whether serial or parallel offset loading has
PAF
LD
PAE
and
threshold can be set at 127 or 1,023 locations from the
PROGRAMMABLE ALMOST-FULL (
on each rising edge of WCLK, are used to load the
(Programmable Almost-Empty flag) and
PAF
FULL FLAG/INPUT READY (
FF
can be programmed independently to switch
/
IR
n
(Full Flag or Input Ready),
.
REN
Figure 1. Block Diagram of Single 32,768 x 18 and 65,536 x 18 Synchronous FIFO
WRITE CLOCK (WCLK)
WRITE ENABLE (
SERIAL ENABLE(
HF
together with
SEN
,
PAE
together with
DATA IN (D
EF
IR
PARTIAL RESET (
EF
and
and
and
/
OR
LOAD (
PAE
(FWFT/SI)
LD
FF
OR
PAF
(Empty Flag or
on each rising
WEN
can be set to
functions are
LD
functions are
0
HF
LD
are always
- D
/ )
pin during
PAF
(Half-full
together
on each
n
)
)
)
)
)
(Pro-
72275
72285
)
IDT
read and write pointers are set to the first location of the FIFO.
The FWFT pin selects IDT Standard mode or FWFT mode.
The
with parallel programming or a partial flag default setting of
1,023 with serial programming. The flags are updated accord-
ing to the timing mode and default offsets selected.
pointers to the first location of the memory. However, the
timing mode, partial flag programming method, and default or
programmed offset settings existing before Partial Reset
remain unchanged. The flags are updated according to the
timing mode and offsets in effect.
a device in mid-operation, when reprogramming partial flags
would be undesirable.
FIFO more than once. A LOW on the
RCLK edge initiates a retransmit operation by setting the read
pointer to the first location of the memory array.
operation, the chip will automatically power down. Once in the
power down state, the standby supply current consumption is
minimized. Initiating any operation (by activating control
inputs) will immediately take the device out of the power down
state.
submicron CMOS technology.
During Master Reset (
The Partial Reset (
The Retransmit function allows data to be reread from the
If, at any time, the FIFO is not actively performing an
The IDT72275/72285 are fabricated using IDT’s high speed
MASTER RESET (
LD
pin selects either a partial flag default setting of 127
READ CLOCK (RCLK)
READ ENABLE (
RETRANSMIT (
EMPTY FLAG/OUTPUT READY (
PROGRAMMABLE ALMOST-EMPTY (
HALF FULL FLAG (
DATA OUT (Q
OUTPUT ENABLE (
PRS
MRS
COMMERCIAL TEMPERATURE RANGE
0
) also sets the read and write
)
) the following events occur: The
- Q
)
n
)
PRS
)
)
)
RT
is useful for resetting
input during a rising
4674 drw 03
/
)
3
)