AM79C978 Advanced Micro Devices, AM79C978 Datasheet - Page 139

• Manufacturer Part Number: AM79C978
• Description: Single-Chip 1/10 Mbps PCI Home Networking Controller
• Manufacturer: Advanced Micro Devices

transmit frame. When the entire
frame is in the MAC Transmit
FIFO, transmission will start re-
gardless of the value in XMTSP.
If the network interface is operat-
ing in half-duplex mode, regard-
less of XMTSP, the FIFO will not
internally overwrite its data until
at least 64 bytes (or the entire
frame if shorter than 64 bytes)
have been transmitted onto the
network. This ensures that for
collisions within the slot time win-
dow, transmit data need not be
rewritten to the Transmit FIFO,
and retries will be handled auton-
omously by the MAC. If the Dis-
able Retry feature is enabled, or if
the network is operating in full-du-
plex mode, the Am79C978 con-
troller
beginning of the frame as soon as
the data is transmitted, because
no collision handling is required in
these modes.
When the SRAM is used and
SRAM_SIZE > 0, there is a re-
striction that the number of bytes
written is a combination of bytes
written into the Bus Transmit
FIFO and the MAC Transmit
FIFO. The Am79C978 controller
supports a mode that will wait un-
til a full packet is available before
commencing with the transmis-
sion of preamble. This mode is
useful in a system where high la-
tencies cannot be avoided. See
Table 33.
Note that when the SRAM is be-
ing used, if the NOUFLO bit
(BCR18, bit 11) is set to 1, there
is the additional restriction that
the complete transmit frame must
be DMA’d into the Am79C978
controller and reside within a
combination of the Bus Transmit
FIFO, the SRAM, and the MAC
Transmit FIFO.
These bits are read/write acces-
sible only when either the STOP
or the SPND bit is set. XMTSP is
set to a value of 01b (64 bytes) af-
ter H_RESET or S_RESET and
is unaffected by STOP.
can
overwrite
the
Am79C978
9-8
XMTSP[1:0]
Table 33. Transmit Start Point Programming
XX
00
01
10
00
01
10
11
11
XMTFW[1:0] Transmit FIFO Watermark. XMT-
SRAM_SIZE
FW specifies the point at which
transmit
based upon the number of bytes
that could be written to the Trans-
mit FIFO without FIFO overflow.
Transmit DMA is requested at
any time when the number of
bytes specified by XMTFW could
be written to the FIFO without
causing Transmit FIFO overflow
and the internal microcode en-
gine has reached a point where
the Transmit FIFO is checked to
determine if DMA servicing is re-
quired.
When operating in the NO-SRAM
mode (no SRAM enabled) and
SRAM_SIZE is set to 0, the Bus
Transmit FIFO and the MAC
Transmit FIFO operate like a sin-
gle FIFO and the watermark val-
ue selected by XMTFW[1:0] sets
the number of FIFO byte loca-
tions that must be available in the
FIFO before receive DMA is re-
quested.
When operating with the SRAM,
the Bus Transmit FIFO and the
MAC Transmit FIFO operate in-
dependently on the bus side and
MAC side of the SRAM, respec-
tively. In this case, the watermark
value set by XMTFW[1:0] sets the
number of FIFO byte locations
that must be available in the Bus
Transmit FIFO. See Table 34
>0
>0
>0
>0
>0
0
0
0
0
DMA
NOUFLO bit is set
Full Packet when
Bytes Written
Full Packet
220 max
is
128
128
20
64
36
64
requested,
139