MA330028 Microchip Technology, MA330028 Datasheet - Page 123

• Manufacturer Part Number: MA330028
• Description: Daughter Cards & OEM Boards dsPIC33EP64MC504 PIM
• Manufacturer: Microchip Technology

Specifications of MA330028

• Rohs: yes
• Product: Daughter Cards
• Core: dsPIC
• Description/function: Plug-in-module with dsPIC33EP64MC504 device for use with DM330021 and DM330023 motor control development board
• Interface Type: CAN, I2C, SPI
• Operating Supply Voltage: 3 to 3.6 V
• Tool Is For Evaluation Of: dsPIC33EP64MC504
• For Use With: DM330021, DM330023

REGISTER 6-1:
© 2011-2012 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13-12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4
Note 1:
TRAPR
R/W-0
R/W-0
EXTR
2:
All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
TRAPR: Trap Reset Flag bit
1 = A Trap Conflict Reset has occurred
0 = A Trap Conflict Reset has not occurred
IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit
1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an
0 = An illegal opcode or uninitialized W Reset has not occurred
Unimplemented: Read as ‘0’
VREGSF: Flash Voltage Regulator Standby During Sleep bit
1 = Flash Voltage regulator is active during Sleep
0 = Flash Voltage regulator goes into Standby mode during Sleep
Unimplemented: Read as ‘0’
CM: Configuration Mismatch Flag bit
1 = A configuration mismatch Reset has occurred.
0 = A configuration mismatch Reset has NOT occurred
VREGS: Voltage Regulator Standby During Sleep bit
1 = Voltage regulator is active during Sleep
0 = Voltage regulator goes into Standby mode during Sleep
EXTR: External Reset (MCLR) Pin bit
1 = A Master Clear (pin) Reset has occurred
0 = A Master Clear (pin) Reset has not occurred
SWR: Software Reset (Instruction) Flag bit
1 = A RESET instruction has been executed
0 = A RESET instruction has not been executed
SWDTEN: Software Enable/Disable of WDT bit
1 = WDT is enabled
0 = WDT is disabled
WDTO: Watchdog Timer Time-out Flag bit
1 = WDT time-out has occurred
0 = WDT time-out has not occurred
IOPUWR
R/W-0
R/W-0
SWR
Address Pointer caused a Reset
RCON: RESET CONTROL REGISTER
W = Writable bit
‘1’ = Bit is set
SWDTEN
R/W-0
U-0
—
(2)
WDTO
R/W-0
U-0
Preliminary
—
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
VREGSF
SLEEP
R/W-0
R/W-0
(2)
(1)
R/W-0
IDLE
U-0
—
x = Bit is unknown
R/W-0
R/W-1
BOR
CM
DS70657E-page 123
VREGS
R/W-0
R/W-1
POR
bit 8
bit 0