KP-F1 Panduit Corp, KP-F1 Datasheet - Page 289

• Manufacturer Part Number: KP-F1
• Description: KIT FERRULE NONINS AWG22-14
• Manufacturer: Panduit Corp
• Series: Pan-Term®r
• Type: Ferrule kitr

Specifications of KP-F1

• Kit Type: Ferrule - Wire End
• Values: 370 pcs - Assorted Non-Insulated 22 ~ 14 AWG Ferrules
• Kit Contents: 500 Pieces Of F75-6, 400 Pieces Of F76-6 & F77-6, 300 Pieces Of F78-7, 200 Pieces Of F80-7
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Note: Panduit assumes no liability for the accuracy or completeness of this list.
Part Number System for Panduct
Installation Tips:
Application of Latex Paint on Panduct
Cutting Wiring Duct and Cover
For small quantities, use the DCT duct cutting tool on page C1.34. For larger quantities use a miter cutting
saw blade for clean burr-free cuts. Recommended blade: Carbide 80T or 100T; .90" thickness, .125 kerf.
Recommended Precaution when Using Type NNC and NE Wiring Duct
Cleaning solvents and cutting fluids that contain any of the following chemical agents should not come in
contact with type NNC or type NE wiring duct. These chemicals are known to cause stress cracking in the
halogen-free PPO material.
G
F
FL
FS
H
HN
HS
D
NNC = Halogen-Free Design
NE
MC = Metric Narrow Slot Design
Type
G
= Wide Slot
= Narrow Slot
= Flexible Duct
= Solid Wall Flush Design
= Wide Slot Hinged Design
= Narrow Slot Hinged Design
= Solid Wall Hinged Design
= Round Hole Flush Design
= Halogen-Free Wide Slot Design
Flush Design
Flush Design
• Hydrocarbons
• Phenols
• Ketones
• Amines
• Ethers
• Organic, inorganic and oxidizing acids
• Petrol
Nominal Width
In. or mm
.5
For technical assistance in the U.S., call 866-405-6654 (outside the U.S., see inside back cover for directory)
The following is recommended to properly prepare the surface of the
wiring duct/raceway and covers for the best adhesion of latex paint:
X
1. Clean surface with mild soap and water solution or mineral spirits
2. Using a sanding pad (such as synthetic stripping pad or medium/fine
3. Apply a coat of all-purpose 100% acrylic primer and allow to dry.
4. Apply the desired topcoat of latex paint and allow to dry.
5. Install the wiring duct/raceway and covers.
with a clean lint free towel. Allow to dry.
steel wool), slightly roughen the surface to be painted.
Nominal Height
®
In. or mm
Wiring Duct
.5
®
Wiring Duct
E L E C T R I C A L S O LU T I O N S
LG = Light
WH = White
BL = Black
IB
IG = International
Color
LG
= Intrinsic Blue
Gray
Gray
Length
Ft. or m
6
-A = Adhesive Backed
NM = No Mounting Holes
-A
= Without Adhesive
(leave blank)
C1.49
Management
Identification
Accessories
Connectors
Connectors
Grounding
Pre-Printed
& Write-On
Protection
Permanent
Solutions
Cable Ties
Terminals
Lockout/
Overview
Steel Ties
& Safety
Stainless
Raceway
Abrasion
Labeling
Systems
Surface
Markers
Tagout
System
Wiring
Labels
Power
Cable
Cable
Index
Duct
E5.
B1.
B2.
B3.
D1.
D2.
D3.
C1.
C2.
C3.
C4.
E1.
E2.
E3.
E4.
A.
F.