C8051F996DK Silicon Laboratories Inc, C8051F996DK Datasheet - Page 294

• Manufacturer Part Number: C8051F996DK
• Description: KIT DEV FOR C8051F996
• Manufacturer: Silicon Laboratories Inc
• Type: MCUr

Specifications of C8051F996DK

• Contents: Board, Batteries, Cables, CDs, Debug Adapter, Documentation, Power Adapter
• Processor To Be Evaluated: C8051F996
• Processor Series: C8051F98x
• Interface Type: USB
• Operating Supply Voltage: 3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: C8051F996
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1963

C8051F99x-C8051F98x
25.3.3. SmaRTClock/External Oscillator Capture Mode
The Capture Mode in Timer 3 allows either SmaRTClock or the external oscillator period to be measured
against the system clock or the system clock divided by 12. SmaRTClock and the external oscillator period
can also be compared against each other.
Setting TF3CEN to 1 enables the SmaRTClock/External Oscillator Capture Mode for Timer 3. In this mode,
T3SPLIT should be set to 0, as the full 16-bit timer is used.
When Capture Mode is enabled, a capture event will be generated either every SmaRTClock rising edge
or every 8 external clock cycles, depending on the T3XCLK1 setting. When the capture event occurs, the
contents of Timer 3 (TMR3H:TMR3L) are loaded into the Timer 3 reload registers (TMR3RLH:TMR3RLL)
and the TF3H flag is set (triggering an interrupt if Timer 3 interrupts are enabled). By recording the differ-
ence between two successive timer capture values, the SmaRTClock or external clock period can be
determined with respect to the Timer 3 clock. The Timer 3 clock should be much faster than the capture
clock to achieve an accurate reading.
For example, if T3ML = 1b, T3XCLK1 = 0b, and TF3CEN = 1b, Timer 3 will clock every SYSCLK and cap-
ture every SmaRTClock rising edge. If SYSCLK is 24.5 MHz and the difference between two successive
captures is 350 counts, then the SmaRTClock period is as follows:
350 x (1 / 24.5 MHz) = 14.2 µs.
This mode allows software to determine the exact frequency of the external oscillator in C and RC mode or
the time between consecutive SmaRTClock rising edges, which is useful for determining the SmaRTClock
frequency.
294
E xtern al C lock/8
E xte rna l C lock/8
S m a R T C lo ck
S Y S C LK /12
S m aR T C loc k
S Y S C LK
T 3X C L K [1:0]
T 3X C L K 1
X 0
01
11
1
0
Figure 25.9. Timer 3 Capture Mode Block Diagram
M
H
T
3
M
0
1
T
3
L
C K C O N
M
T
2
H
T
M
2
L
M
T
1
T F 3 C E N
M
T
0
S
C
A
1
T R 3
S
C
A
0
Rev. 1.0
C ap ture
T C L K
T M R 3R LL T M R 3 R LH
T M R 3L
T M R 3 H
T 3X C L K 1
T 3X C L K 0
T F 3 C E N
T 3 S P LIT
T F 3 L E N
T F 3H
T F 3 L
T R 3
Interrupt