EVAL-ADUC832QSZ Analog Devices Inc, EVAL-ADUC832QSZ Datasheet - Page 62

• Manufacturer Part Number: EVAL-ADUC832QSZ
• Description: KIT DEV FOR ADUC832 QUICK START
• Manufacturer: Analog Devices Inc
• Series: QuickStart™ Kitr
• Type: MCUr

Specifications of EVAL-ADUC832QSZ

• Contents: Evaluation Board, Cable, Power Supply, Software and Documentation
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: ADuC832
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: EVAL-ADUC832QS; EVAL-ADUC832QS

ADuC832
DUAL DATA POINTERS
The ADuC832 incorporates two data pointers. The second data
pointer is a shadow data pointer and is selected via the data
pointer control SFR (DPCON). DPCON also includes features
such as automatic hardware postincrement and postdecrement,
as well as automatic data pointer toggle. DPCON is described in
Table 30.
Table 30. DPCON SFR Bit Designations
Bit
[7]
[6]
[5:4]
[3:2]
[1]
[0]
Notes
This is the only section where the main and shadow data
pointers are distinguished. Everywhere else in this data sheet
wherever the DPTR is mentioned, operation on the active
DPTR is implied.
Only MOVC/MOVX @DPTR instructions are relevant in Table 30.
MOVC/MOVX PC/@Ri instructions do not cause the DPTR to
automatically postincrement or postdecrement.
To illustrate the operation of DPCON, the following code copies
256 bytes of code memory at Address D000H into XRAM
starting from Address 0000H.
The following code uses 16 bytes and 2054 cycles. To perform
this on a standard 8051 requires approximately 33 bytes and
7172 cycles (depending on how it is implemented).
Name
Reserved
DPT
DP1m[1:0]
DP0m[1:0]
Reserved
DPSEL
Description
Reserved for future use.
Data pointer automatic toggle enable.
Cleared by user to disable auto swapping of the DPTR. Set in user software to enable automatic toggling of the DPTR
after each MOVX or MOVC instruction.
Shadow data pointer mode.
These two bits enable extra modes of the shadow data pointer operation, allowing for more compact and more
efficient code size and execution.
DP1m1
0
0
1
1
Main data pointer mode. These two bits enable extra modes of the main data pointer operation, allowing for more
compact and more efficient code size and execution.
DP0m1
0
0
1
1
This bit is not implemented to allow the INC DPCON instruction to toggle the data pointer without incrementing the
rest of the SFR.
Data pointer select.
Cleared by user to select the main data pointer. This means that the contents of this 24-bit register are placed into the
DPL, DPH, and DPP SFRs.
Set by the user to select the shadow data pointer. This means that the contents of a separate 24-bit register appears in
the DPL, DPH, and DPP SFRs.
DP1m0
0
1
0
1
DP0m0
0
1
0
1
Behavior of Shadow Data Pointer
8052 behavior
DPTR is postincremented after a MOVX or a MOVC instruction.
DPTR is postdecremented after a MOVX or MOVC instruction.
DPTR LSB is toggled after a MOVX or MOVC instruction. (This instruction can be useful for moving
8-bit blocks to/from 16-bit devices.)
Behavior of the Main Data Pointer
8052 behavior
1 DPTR is postincremented after a MOVX or a MOVC instruction.
DPTR is postdecremented after a MOVX or MOVC instruction.
DPTR LSB is toggled after a MOVX or MOVC instruction. (This instruction can be useful for moving
8-bit blocks to/from 16-bit devices.)
Rev. A | Page 62 of 92
DPCON (DATA POINTER CONTROL SFR)
SFR Address:
Power-On Default Value:
Bit Addressable:
MOV
MOV
MOV
MOVELOOP:
CLR
MOVC A,@A+DPTR
MOVX @DPTR,A
MOV
JNZ
DPTR,#0
DPCON,#55H
DPTR,#0D000H
A
A, DPL
MOVELOOP
; Main DPTR = 0
; Select shadow DPTR
; DPTR1 increment mode,
; DPTR0 increment mode
; DPTR auto toggling on
; Shadow DPTR = D000H
; Get data
; Post Inc DPTR
; Swap to Main DPTR (Data)
; Put ACC in XRAM
; Increment main DPTR
; Swap Shadow DPTR (Code)
A7H
00H
No