INDART-ONE/FSL SofTec Microsystems SRL, INDART-ONE/FSL Datasheet - Page 57
INDART-ONE/FSL
Manufacturer Part Number
INDART-ONE/FSL
Description
PROG/DEBUG FOR HC08/HCS08/HCS12
Manufacturer
SofTec Microsystems SRL
Series
inDARTr
Type
In-Circuit, Real-Time Debugger/Programmerr
Datasheets
1.INDART-ONEFSL.pdf
(2 pages)
2.INDART-ONEFSL.pdf
(140 pages)
3.INDART-ONEFSL.pdf
(2 pages)
Specifications of INDART-ONE/FSL
Contents
In-circuit debugger/programmer unit, Cables, Evaluation Board and Software
For Use With/related Products
Freescale HC08/S08/RS08/S12/S12X
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
520-1038
INDART-ONE
INDART-ONE
- Current page: 57 of 140
- Download datasheet (2Mb)
5 Working with HC08 Devices
5.1 Debugging Limitations
Since inDART-One is based on the in-chip debugging features of the HC08
family of microcontrollers, some hardware and software limitations apply.
The main ones are listed below; for the complete list of limitations please
refer to the microcontroller’s data sheet.
5.2 Communication Settings
inDART-One must be configured properly so that MON08 communication
with the target device can be established correctly.
The pin dedicated to the host communication is reserved—in particular,
the corresponding bit in the Data Direction Register must not be
changed (must be left to input);
The Break Module peripheral is reserved, and only one hardware
breakpoint is available—however, you can insert a “swi” instruction
into your code to generate a software breakpoint;
The “swi” instruction is reserved and can be only used to generate a
software breakpoint;
Step commands which involve the execution of two or more Assembly
instructions waste one hardware breakpoint—therefore, if one
breakpoint was already set by the user, the step command cannot be
executed;
The “Halt” debugging command (in the CodeWarrior HC08 user
interface) will not work unless the IRQ interrupt is properly handled;
13 bytes of stack are wasted by the on-chip monitor—therefore the
addresses from SP-13 to SP are reserved;
Registers which affect the target microcontroller’s clock speed must not
be changed during debugging sessions.
inDART-One User's Manual
55
5
Related parts for INDART-ONE/FSL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT DEBUGGER IN-CIRC ST7 FLASH
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT DEBUGGER IN-CIRC ST7 USB
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER FOR ST7
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN FOR ST7
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCS12
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCS12
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCS12
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCSO8
Manufacturer:
SofTec Microsystems SRL
Datasheet: