INDART-ONE/FSL SofTec Microsystems SRL, INDART-ONE/FSL Datasheet - Page 59
INDART-ONE/FSL
Manufacturer Part Number
INDART-ONE/FSL
Description
PROG/DEBUG FOR HC08/HCS08/HCS12
Manufacturer
SofTec Microsystems SRL
Series
inDARTr
Type
In-Circuit, Real-Time Debugger/Programmerr
Datasheets
1.INDART-ONEFSL.pdf
(2 pages)
2.INDART-ONEFSL.pdf
(140 pages)
3.INDART-ONEFSL.pdf
(2 pages)
Specifications of INDART-ONE/FSL
Contents
In-circuit debugger/programmer unit, Cables, Evaluation Board and Software
For Use With/related Products
Freescale HC08/S08/RS08/S12/S12X
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
520-1038
INDART-ONE
INDART-ONE
- Current page: 59 of 140
- Download datasheet (2Mb)
inDART-One User's Manual
inDART-One’s MON08 connector can behave as a standard (Multilink
compatible) MON08 connector or as an enhanced MON08 connector. The
former is suggested for most target boards, while the latter is compatible with
SofTec Microsystems inDART-HC08 and can be specifically used in
conjunction with Freescale ICS boards or with SofTec Microsystems demo
boards. In this case less target I/O lines will be wasted.
For device-specific information, see “MON08 Target Connections” later in
this chapter.
The “MON08 OSC Signal” parameter (available in the standard MON08
mode) allows you to select whether inDART-One generates a clock signal at
the pin 13 of the MON08 connector. This signal can be used as an auxiliary
clock source, and is particularly useful when the target microcontroller
requires an external clock which is not otherwise available on the target
board.
The “External Clock Divider” parameter should always be set to “DIV 4” in
order to guarantee that, in monitor mode, all of the target microcontroller’s
peripherals run at the same speed they do in user mode. If, however, you
need to speed up program execution, you can set this parameter to “DIV 2”,
5
therefore doubling the microcontroller’s speed in monitor mode. Note,
however, that not all peripherals will work at this doubled speed.
5.2.2 Power Settings
The parameters in this group are used by inDART-One to determine how to
force the target microcontroller to enter the monitor mode.
57
Related parts for INDART-ONE/FSL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT DEBUGGER IN-CIRC ST7 FLASH
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT DEBUGGER IN-CIRC ST7 USB
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER FOR ST7
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN FOR ST7
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCS12
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCS12
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCS12
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCSO8
Manufacturer:
SofTec Microsystems SRL
Datasheet: