INDART-ONE/FSL SofTec Microsystems SRL, INDART-ONE/FSL Datasheet - Page 63
INDART-ONE/FSL
Manufacturer Part Number
INDART-ONE/FSL
Description
PROG/DEBUG FOR HC08/HCS08/HCS12
Manufacturer
SofTec Microsystems SRL
Series
inDARTr
Type
In-Circuit, Real-Time Debugger/Programmerr
Datasheets
1.INDART-ONEFSL.pdf
(2 pages)
2.INDART-ONEFSL.pdf
(140 pages)
3.INDART-ONEFSL.pdf
(2 pages)
Specifications of INDART-ONE/FSL
Contents
In-circuit debugger/programmer unit, Cables, Evaluation Board and Software
For Use With/related Products
Freescale HC08/S08/RS08/S12/S12X
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
520-1038
INDART-ONE
INDART-ONE
- Current page: 63 of 140
- Download datasheet (2Mb)
The “Target Baud Rate” parameter specifies the MON08 serial line’s baud
rate used to enter the monitor mode. inDART-One can automatically
determine the correct target baud rate in the most common situations; the
“Automatic Detection” is the default option. However, if for some reasons
the automatic detection doesn’t work, you still have the possibility to select
the baud rate manually.
As an aid, a baud rate calculator is provided. Just click on the “Baud Rate
Calc.” button and enter the microcontroller external clock frequency and the
appropriate baud rate will be calculated for you. Please note, however, that
this method only works if the IRQ line of the microcontroller is tied to the IRQ
line of the MON08 connector. In all other cases, again, you must consult the
data sheet of the target microcontroller.
i
Figure 5.5: MON08 Communication Settings: Baud Rate Calculator
Note: when using the manual baud rate selection, keep in
mind that the correct target baud rate value to use critically
depends on the target hardware; different target
configurations require different baud rate values. It is highly
recommended that you consult the data sheet of the target
microcontroller (the section about entering the monitor
mode) in order to calculate the correct baud rate to set. An
improper target baud rate value may result in programming
errors.
inDART-One User's Manual
61
5
Related parts for INDART-ONE/FSL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT DEBUGGER IN-CIRC ST7 FLASH
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT DEBUGGER IN-CIRC ST7 USB
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER FOR ST7
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN FOR ST7
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCS12
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCS12
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCS12
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCO8
Manufacturer:
SofTec Microsystems SRL
Datasheet:
Part Number:
Description:
KIT DESIGN USB FOR HCSO8
Manufacturer:
SofTec Microsystems SRL
Datasheet: