PIC18F66J11-I/PT Microchip Technology, PIC18F66J11-I/PT Datasheet - Page 290

• Manufacturer Part Number: PIC18F66J11-I/PT
• Description: IC PIC MCU FLASH 32KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F66J11-I/PT

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 52
• Program Memory Type: FLASH
• Ram Size: 3930 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 52
• Ram Memory Size: 3.837890625KB
• Cpu Speed: 48MHz
• No. Of Timers: 5
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3904 B
• Interface Type: EUSART, I2C, MSSP, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 52
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 1.8|2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162091 - HEADER MPLAB ICD2 18F87J11 64/80MA180020 - MODULE PLUG-IN HPC EXPL 18F87J11AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Synchronous Master mode in that the shift clock is sup-
PIC18F87J11 FAMILY
TABLE 20-8:
20.4
Synchronous Slave mode is entered by clearing bit,
CSRC (TXSTAx<7>). This mode differs from the
plied externally at the CKx pin (instead of being supplied
internally in Master mode). This allows the device to
transfer or receive data while in any low-power mode.
20.4.1
The operation of the Synchronous Master and Slave
modes is identical, except in the case of Sleep mode.
If two words are written to the TXREGx and then the
SLEEP instruction is executed, the following will occur:
a)
b)
c)
d)
e)
DS39778D-page 290
INTCON
PIR1
PIE1
IPR1
PIR3
PIE3
IPR3
RCSTAx
RCREGx
TXSTAx
BAUDCONx ABDOVF
SPBRGHx EUSARTx Baud Rate Generator Register High Byte
SPBRGx
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
Name
The first word will immediately transfer to the
TSR register and transmit.
The second word will remain in the TXREGx
register.
Flag bit, TXxIF, will not be set.
When the first word has been shifted out of TSR,
the TXREGx register will transfer the second
word to the TSR and flag bit, TXxIF, will now be
set.
If enable bit, TXxIE, is set, the interrupt will wake
the chip from Sleep. If the global interrupt is
enabled, the program will branch to the interrupt
vector.
EUSART Synchronous
Slave Mode
EUSART SYNCHRONOUS
SLAVE TRANSMISSION
EUSARTx Receive Register
EUSARTx Baud Rate Generator Register Low Byte
GIE/GIEH PEIE/GIEL TMR0IE
SSP2IE
SSP2IP
SSP2IF
PMPIE
PMPIP
PMPIF
CSRC
SPEN
Bit 7
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
BCL2IF
BCL2IE
BCL2IP
RCIDL
ADIF
ADIE
ADIP
Bit 6
RX9
TX9
RXDTP
RC1IE
RC1IP
RC2IE
RC2IP
RC1IF
RC2IF
SREN
TXEN
Bit 5
TXCKP
INT0IE
TX1IF
TX1IE
TX1IP
TX2IF
TX2IE
TX2IP
CREN
SYNC
Bit 4
TMR4IF
TMR4IE
TMR4IP
SSP1IE
SSP1IP
ADDEN
SSP1IF
SENDB
BRG16
RBIE
Bit 3
To set up a Synchronous Slave Transmission:
1.
2.
3.
4.
5.
6.
7.
8.
Enable the synchronous slave serial port by
setting bits, SYNC and SPEN, and clearing bit,
CSRC.
Clear bits, CREN and SREN.
If interrupts are desired, set enable bit, TXxIE.
If 9-bit transmission is desired, set bit, TX9.
Enable the transmission by setting enable bit,
TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit, TX9D.
Start transmission by loading data to the
TXREGx register.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
TMR0IF
CCP1IF
CCP1IE
CCP1IP
CCP5IF
CCP5IE
CCP5IP
BRGH
FERR
Bit 2
—
TMR2IF
TMR2IE
TMR2IP
CCP4IF
CCP4IE
CCP4IP
INT0IF
OERR
TRMT
WUE
Bit 1
© 2009 Microchip Technology Inc.
TMR1IF
TMR1IE
TMR1IP
CCP3IF
CCP3IE
CCP3IP
ABDEN
RX9D
TX9D
RBIF
Bit 0
Reset Values
on Page:
57
60
60
60
60
60
60
59
59
59
61
61
61