PIC18F66J11-I/PT Microchip Technology, PIC18F66J11-I/PT Datasheet - Page 39

• Manufacturer Part Number: PIC18F66J11-I/PT
• Description: IC PIC MCU FLASH 32KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F66J11-I/PT

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 52
• Program Memory Type: FLASH
• Ram Size: 3930 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 52
• Ram Memory Size: 3.837890625KB
• Cpu Speed: 48MHz
• No. Of Timers: 5
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3904 B
• Interface Type: EUSART, I2C, MSSP, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 52
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 1.8|2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162091 - HEADER MPLAB ICD2 18F87J11 64/80MA180020 - MODULE PLUG-IN HPC EXPL 18F87J11AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

2.5
The PIC18F87J11 Family of devices includes an
internal oscillator block which generates two different
clock signals; either can be used as the microcon-
troller’s clock source. This may eliminate the need for
an external oscillator circuit on the OSC1 and/or OSC2
pins.
The main output is the Fast RC oscillator, or INTOSC,
an 8 MHz clock source which can be used to directly
drive the device clock. It also drives a postscaler, which
can provide a range of clock frequencies from 31 kHz
to 4 MHz. INTOSC is enabled when a clock frequency
from 125 kHz to 8 MHz is selected. The INTOSC out-
put can also be enabled when 31 kHz is selected,
depending on the INTSRC bit (OSCTUNE<7>).
The other clock source is the internal RC oscillator
(INTRC), which provides a nominal 31 kHz output.
INTRC is enabled if it is selected as the device clock
source; it is also enabled automatically when any of the
following are enabled:
• Power-up Timer
• Fail-Safe Clock Monitor
• Watchdog Timer
• Two-Speed Start-up
These features are discussed in greater detail in
Section 24.0 “Special Features of the CPU”.
The clock source frequency (INTOSC direct, INTOSC
with postscaler or INTRC direct) is selected by config-
uring the IRCF bits of the OSCCON register. The
default frequency on device Resets is 4 MHz.
2.5.1
Using the internal oscillator as the clock source elimi-
nates the need for up to two external oscillator pins,
which can then be used for digital I/O. Two distinct
oscillator configurations, which are determined by the
FOSC Configuration bits, are available:
• In INTIO1 mode, the OSC2 pin outputs F
• In INTIO2 mode, OSC1 functions as RA7 and
© 2009 Microchip Technology Inc.
while OSC1 functions as RA7 (see Figure 2-6) for
digital input and output.
OSC2 functions as RA6 (see Figure 2-7), both for
digital input and output.
Internal Oscillator Block
INTIO MODES
OSC
/4,
PIC18F87J11 FAMILY
FIGURE 2-6:
FIGURE 2-7:
2.5.2
The 4x Phase Locked Loop (PLL) can be used with the
internal oscillator block to produce faster device clock
speeds than are normally possible with the internal
oscillator sources. When enabled, the PLL produces a
clock speed of 16 MHz or 32 MHz.
PLL operation is controlled through software. The con-
trol bit, PLLEN (OSCTUNE<6>), is used to enable or
disable its operation. The PLL is available only to
INTOSC when the device is configured to use one of
the INTPLL modes as the primary clock source
(FOSC2:FOSC0 = 011 or 010). Additionally, the PLL
will only function when the selected output frequency is
either 4 MHz or 8 MHz (OSCCON<6:4> = 111 or 110).
Like the INTIO modes, there are two distinct INTPLL
modes available:
• In INTPLL1 mode, the OSC2 pin outputs F
• In INTPLL2 mode, OSC1 functions as RA7 and
while OSC1 functions as RA7 for digital input and
output. Externally, this is identical in appearance
to INTIO1 (Figure 2-6).
OSC2 functions as RA6, both for digital input and
output. Externally, this is identical to INTIO2
(Figure 2-7).
F
RA7
RA6
OSC
RA7
/4
INTPLL MODES
INTIO1 OSCILLATOR MODE
INTIO2 OSCILLATOR MODE
I/O (OSC1)
I/O (OSC2)
I/O (OSC1)
OSC2
PIC18F87J11
PIC18F87J11
DS39778D-page 39
OSC
/4,