PIC18F4320-I/PT Microchip Technology, PIC18F4320-I/PT Datasheet - Page 225

• Manufacturer Part Number: PIC18F4320-I/PT
• Description: IC MCU FLASH 4KX16 A/D 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4320-I/PT

• Core Size: 8-Bit
• Program Memory Size: 8KB (4K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44PT3 - SOCKET TRAN ICE 44MQFP/TQFPAC164305 - MODULE SKT FOR PM3 44TQFP444-1001 - DEMO BOARD FOR PICMICRO MCUAC164020 - MODULE SKT PROMATEII 44TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

20.2
A single comparator is shown in Figure 20-2, along with
the relationship between the analog input levels and
the digital output. When the analog input at V
than the analog input V
is a digital low level. When the analog input at V
greater than the analog input V
comparator is a digital high level. The shaded areas of
the output of the comparator in Figure 20-2 represent
the uncertainty due to input offsets and response time.
20.3
An external or internal reference signal may be used
depending on the comparator operating mode. The
analog signal present at V
at V
adjusted accordingly (Figure 20-2).
FIGURE 20-2:
20.3.1
When external voltage references are used, the
comparator module can be configured to have the com-
parators operate from the same or different reference
sources. However, threshold detector applications may
require the same reference. The reference signal must
be between V
pin of the comparator(s).
© 2007 Microchip Technology Inc.
Output
V
V
Output
IN
V
IN
V
IN
IN–
IN+
-
+
+ and the digital output of the comparator is
V
V
IN
IN
Comparator Operation
Comparator Reference
+
-
EXTERNAL REFERENCE SIGNAL
SS
and V
+
–
IN
SINGLE COMPARATOR
DD
-, the output of the comparator
IN
and can be applied to either
- is compared to the signal
IN
-, the output of the
Output
IN
PIC18F2220/2320/4220/4320
+ is less
IN
+ is
20.3.2
The comparator module also allows the selection of an
internally generated voltage reference for the compara-
tors. Section 21.0 “Comparator Voltage Reference
Module” contains a detailed description of the compar-
ator voltage reference module that provides this signal.
The internal reference signal is used when comparators
are in mode, CM2:CM0 = 110 (Figure 20-1). In this
mode, the internal voltage reference is applied to the
V
Depending on the setting of the CVROE bit
(CVRCON<6>), the voltage reference may also be
available on pin RA2.
20.4
Response time is the minimum time, after selecting a
new reference voltage or input source, before the
comparator output has a valid level. If the internal ref-
erence is changed, the maximum delay of the internal
voltage reference must be considered when using the
comparator outputs. Otherwise, the maximum delay of
the comparators should be used (see Table 26-2 in
Section 26.0 “Electrical Characteristics”).
20.5
The comparator outputs are read through the CMCON
register. These bits are read-only. The comparator
outputs may also be directly output to the RA4 and RA5
I/O pins. When enabled, multiplexers in the output path
of the RA4 and RA5 pins will switch and the output of
each pin will be the unsynchronized output of the com-
parator. The uncertainty of each of the comparators is
related to the input offset voltage and the response time
given in the specifications. Figure 20-3 shows the
comparator output block diagram.
The TRISA bits will still function as an output enable/
disable for the RA4 and RA5 pins while in this mode.
The polarity of the comparator outputs can be changed
using the C2INV and C1INV bits (CMCON<4:5>).
IN
Note 1: When reading the PORT register, all pins
+ pin of both comparators.
2: Analog levels on any pin defined as a
Comparator Response Time
Comparator Outputs
INTERNAL REFERENCE SIGNAL
configured as analog inputs will read as a
‘0’. Pins configured as digital inputs will
convert an analog input according to the
Schmitt Trigger input specification.
digital input may cause the input buffer to
consume more current than is specified.
DS39599G-page 223