PIC18F4320-I/PT Microchip Technology, PIC18F4320-I/PT Datasheet - Page 37

• Manufacturer Part Number: PIC18F4320-I/PT
• Description: IC MCU FLASH 4KX16 A/D 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4320-I/PT

• Core Size: 8-Bit
• Program Memory Size: 8KB (4K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44PT3 - SOCKET TRAN ICE 44MQFP/TQFPAC164305 - MODULE SKT FOR PM3 44TQFP444-1001 - DEMO BOARD FOR PICMICRO MCUAC164020 - MODULE SKT PROMATEII 44TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

3.3.3
In RC_IDLE mode, the CPU is disabled but the periph-
erals continue to be clocked from the internal oscillator
block using the INTOSC multiplexer. This mode allows
for controllable power conservation during Idle periods.
This mode is entered by setting the IDLEN bit, setting
SCS1 (SCS0 is ignored) and executing a SLEEP
instruction. The INTOSC multiplexer may be used to
select a higher clock frequency by modifying the IRCF
bits before executing the SLEEP instruction. When the
clock source is switched to the INTOSC multiplexer
(see Figure 3-7), the primary oscillator is shut down
and the OSTS bit is cleared.
If the IRCF bits are set to a non-zero value (thus
enabling the INTOSC output), the IOFS bit becomes
set after the INTOSC output becomes stable, in about
1 ms. Clocks to the peripherals continue while the
INTOSC source stabilizes. If the IRCF bits were previ-
ously at a non-zero value before the SLEEP instruction
FIGURE 3-7:
FIGURE 3-8:
© 2007 Microchip Technology Inc.
INTRC
OSC1
CPU
Clock
Peripheral
Clock
Program
Counter
CPU Clock
Multiplexer
Note 1: T
PLL Clock
Peripheral
Program
INTOSC
Counter
Output
OSC1
Clock
Q1
RC_IDLE MODE
Wake-up from Interrupt Event
OST
Q2
PC
= 1024 T
Q3
PC
Q4
Q4
TIMING TRANSITION TO RC_IDLE MODE
TIMING TRANSITION FOR WAKE FROM RC_RUN MODE (RC_RUN TO PRI_RUN)
OSC
Q1
; T
Q1
PLL
1
T
OST
= 2 ms (approx). These intervals are not shown to scale.
(1)
2
Q2
PC + 2
3
Clock Transition
T
OSTS bit Set
Q3
PLL
PIC18F2220/2320/4220/4320
4
(1)
Q4
5
PC + 2
6
Q1
1
2
7
was executed and the INTOSC source was already
stable, the IOFS bit will remain set. If the IRCF bits are
all clear, the INTOSC output is not enabled and the
IOFS bit will remain clear; there will be no indication of
the current clock source.
When a wake-up event occurs, the peripherals con-
tinue to be clocked from the INTOSC multiplexer. After
a 10 μs delay following the wake-up event, the CPU
begins executing code, being clocked by the INTOSC
multiplexer. The microcontroller operates in RC_RUN
mode until the primary clock becomes ready. When the
primary clock becomes ready, a clock switch back to
the primary clock occurs (see Figure 3-8). When the
clock switch is complete, the IOFS bit is cleared, the
OSTS bit is set and the primary clock is providing the
system clock. The IDLEN and SCS bits are not affected
by the wake-up. The INTRC source will continue to run
if either the WDT or the Fail-Safe Clock Monitor is
enabled.
Clock Transition
3
8
4
5
PC + 4
6
7
8
Q2
Q3 Q4
DS39599G-page 35
Q1
PC + 6
Q2
Q3