MCF5216CVF66 Freescale Semiconductor, MCF5216CVF66 Datasheet - Page 447

• Manufacturer Part Number: MCF5216CVF66
• Description: IC MPU 32BIT COLDF 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF521xr

Specifications of MCF5216CVF66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 142
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Controller Family/series: ColdFire
• Ram Memory Size: 64KB
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of Pwm Channels: 8
• Operating Temperature Range: -40°C To +85°C
• No. Of Pins: 256
• Rohs Compliant: No
• Package: 256MA-BGA
• Device Core: ColdFire
• Family Name: MCF521x
• Maximum Speed: 66 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 142
• Interface Type: QSPI/UART/I2C/CAN
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 8
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

23.5.1.2
The UART is capable of generating two internal DMA request signals: transmit and receive.
The transmit DMA request signal is asserted when the TXRDY (transmitter ready) in the UART interrupt
status register (UISRn[TXRDY]) is set. When the transmit DMA request signal is asserted, the DMA can
initiate a data copy, reading the next character transmitted from memory and writing it into the UART
transmit buffer (UTBn). This allows the DMA channel to stream data from memory to the UART for
transmission without processor intervention. After the entire message has been moved into the UART, the
DMA would typically generate an end-of-data-transfer interrupt request to the CPU. The resulting
interrupt service routine (ISR) could query the UART programming model to determine the
end-of-transmission status.
Similarly, the receive DMA request signal is asserted when the FIFO full or receive ready
(FFULL/RXRDY) flag in the interrupt status register (UISRn[FFULL/RXRDY]) is set. When the receive
DMA request signal is asserted, the DMA can initiate a data move, reading the appropriate characters from
the UART receive buffer (URBn) and storing them in memory. This allows the DMA channel to stream
data from the UART receive buffer into memory without processor intervention. After the entire message
has been moved from the UART, the DMA would typically generate an end-of-data-transfer interrupt
request to the CPU. The resulting interrupt service routine (ISR) should query the UART programming
model to determine the end-of-transmission status. In typical applications, the receive DMA request
should be configured to use RXRDY directly (and not FFULL) to remove any complications related to
retrieving the final characters from the FIFO buffer.
The implementation described in this section allows independent DMA processing of transmit and receive
data while continuing to support interrupt notification to the processor for CTS change-of-state and delta
break error managing.
Freescale Semiconductor
3. Unmask appropriate bits in the core’s status register (SR) to enable interrupts.
4. If TXRDY or RXRDY generates interrupt requests, verify that DMAREQC (in the SCM) does not
5. Initialize interrupts in the UART, see
also assign the UART’s TXRDY and RXRDY into DMA channels.
Setting up the UART to Request DMA Service
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
Register
UMR1n
UIMRn
UIMRn
UIMRn
UIMRn
Table 23-13. UART Interrupts
Bit
6
7
2
1
0
Table
RxIRQ
Change of State (COS)
Delta Break
RxFIFO Full
TXRDY
23-13.
Interrupt
UART Modules
23-27