AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 224

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 16-4. Write Burst, 16-bit SDRAM Access
16.7.3
32072G–11/2011
SDRAMC_A[12:0]
D[15:0]
SDWE
SDCS
SDCK
SDRAM Controller Read Cycle
RAS
CAS
The SDRAMC allows burst access, incremental burst of unspecified length or single access. In
all cases, the SDRAMC keeps track of the active row in each bank, thus maximizing perfor-
mance of the SDRAM. If row and bank addresses do not match the previous row/bank address,
then the SDRAMC automatically generates a precharge command, activates the new row and
starts the read command. To comply with the SDRAM timing parameters, additional clock cycles
on SDCK are inserted between precharge and active (t
read (t
read command, additional wait states are generated to comply with the CAS latency (one, two,
or three clock delays specified in the CR register).
For a single access or an incremented burst of unspecified length, the SDRAMC anticipates the
next access. While the last value of the column is returned by the SDRAMC on the bus, the
SDRAMC anticipates the read to the next column and thus anticipates the CAS latency. This
reduces the effect of the CAS latency on the internal bus.
For burst access of specified length (4, 8, 16 words), access is not anticipated. This case leads
to the best performance. If the burst is broken (border, busy mode, etc.), the next access is han-
dled as an incrementing burst of unspecified length.
Row n
t
RCD
RCD
= 3
) commands. These two parameters are set in the CR register of the SDRAMC. After a
Col a
Dna
Col b
Dnb
Col c
Dnc
Col d
Dnd
Col e
Dne
Col f
Dnf
Col g
Dng
RP
) commands and between active and
Col h Col i
Dnh
Dni
Col j
Dnj
Col k
Dnk
Col l
Dnl
224