AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 727

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

• PERRI: Pipe Error Interrupt
• TXSTPI: Transmitted SETUP Interrupt
• UNDERFI: Underflow Interrupt
• TXOUTI: Transmitted OUT Data Interrupt
• RXINI: Received IN Data Interrupt
32072G–11/2011
This bit is cleared when the NAKEDIC bit written to one.
This bit is set when an error occurs on the current bank of the pipe. This triggers an interrupt if the PERRE bit is set. Refers to
the UPERRn register to determine the source of the error.
This bit is cleared when the error source bit is cleared.
This bit is set, for Control endpoints, when the current SETUP bank is free and can be filled. This triggers an interrupt if the
TXSTPE bit is one.
This bit is cleared when the TXSTPIC bit is written to one.
This bit is set, for isochronous and Interrupt IN/OUT pipe, when an error flow occurs. This triggers an interrupt if the UNDERFIE
bit is one.
This bit is set, for Isochronous or interrupt OUT pipe, when a transaction underflow occurs in the current pipe. (the pipe can’t
send the OUT data packet in time because the current bank is not ready). A zero-length-packet (ZLP) will be sent instead of.
This bit is set, for Isochronous or interrupt IN pipe, when a transaction flow error occurs in the current pipe. i.e, the current bank
of the pipe is not free whereas a new IN USB packet is received. This packet is not stored in the bank. For Interrupt pipe, the
overflowed packet is ACKed to respect the USB standard.
This bit is cleared when the UNDERFIEC bit is written to one.
This bit is set when the current OUT bank is free and can be filled. This triggers an interrupt if the TXOUTE bit is one.
This bit is cleared when the TXOUTIC bit is written to one.
This bit is set when a new USB message is stored in the current bank of the pipe. This triggers an interrupt if the RXINE bit is
one.
This bit is cleared when the RXINIC bit is written to one.
727