AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 696

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

• RXSTPI: Received SETUP Interrupt
• RXOUTI: Received OUT Data Interrupt
• TXINI: Transmitted IN Data Interrupt
32072G–11/2011
An underflow can occur during IN stage if the host attempts to read from an empty bank. A zero-length packet is then
automatically sent by the USBB.
An underflow can also occur during OUT stage if the host sends a packet while the bank is already full. Typically, the CPU is not
fast enough. The packet is lost.
Shall be cleared by writing a one to the UNDERFIC bit. This will acknowledge the interrupt.
This bit is inactive (cleared) for bulk and interrupt IN/OUT endpoints and it means RXSTPI for control endpoints.
This bit is set, for control endpoints, to signal that the current bank contains a new valid SETUP packet. This triggers an EPnINT
interrupt if RXSTPE is one.
Shall be cleared by writing a one to the RXSTPIC bit. This will acknowledge the interrupt and free the bank.
This bit is inactive (cleared) for bulk and interrupt IN/OUT endpoints and it means UNDERFI for isochronous IN/OUT endpoints.
This bit is set, for control endpoints, when the current bank contains a bulk OUT packet (data or status stage). This triggers an
EPnINT interrupt if RXOUTE is one.
Shall be cleared for control end points, by writing a one to the RXOUTIC bit. This will acknowledge the interrupt and free the
bank.
This bit is set for isochronous, bulk and, interrupt OUT endpoints, at the same time as FIFOCON when the current bank is full.
This triggers an EPnINT interrupt if RXOUTE is one.
Shall be cleared for isochronous, bulk and, interrupt OUT endpoints, by writing a one to the RXOUTIC bit. This will acknowledge
the interrupt, what has no effect on the endpoint FIFO.
The user then reads from the FIFO and clears the FIFOCON bit to free the bank. If the OUT endpoint is composed of multiple
banks, this also switches to the next bank. The RXOUTI and FIFOCON bits are set/cleared in accordance with the status of the
next bank.
RXOUTI shall always be cleared before clearing FIFOCON.
This bit is inactive (cleared) for isochronous, bulk and interrupt IN endpoints.
This bit is set for control endpoints, when the current bank is ready to accept a new IN packet. This triggers an EPnINT interrupt
if TXINE is one.
This bit is cleared when the TXINIC bit is written to one. This will acknowledge the interrupt and send the packet.
This bit is set for isochronous, bulk and interrupt IN endpoints, at the same time as FIFOCON when the current bank is free.
This triggers an EPnINT interrupt if TXINE is one.
This bit is cleared when the TXINIC bit is written to one. This will acknowledge the interrupt, what has no effect on the endpoint
FIFO.
The user then writes into the FIFO and clears the FIFOCON bit to allow the USBB to send the data. If the IN endpoint is
composed of multiple banks, this also switches to the next bank. The TXINI and FIFOCON bits are set/cleared in accordance
with the status of the next bank.
TXINI shall always be cleared before clearing FIFOCON.
This bit is inactive (cleared) for isochronous, bulk and interrupt OUT endpoints.
696